Question about 2011 Chevrolet Cruze

1 Answer

Where is fuel filter position - 2011 Chevrolet Cruze

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,957 Answers

...inside the gas tank, part of the fuel pump/gas-level assembly; item #6 in this GM parts illustration:
where is fuel filter position - 25672144-cbxkgchp3lmsqhngtniariob-5-0.jpg

Posted on Apr 29, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel filtre


Diesel filters are positioned almost exclusively in the engine compartment though there is generally a prefilter screen fitted inside the fuel tank which rarely needs attention.

Petrol filters can be almost anywhere. Some cars have a lifetime filter fitted inside the fuel tank but the majority of vehicles have a prefilter screen inside the tank and a replaceable filter positioned in a convenient place along the fuel supply line.
Underneath close to the fuel tank or in the engine compartment close to the bulkhead are two common positions.

Mar 01, 2015 | Cars & Trucks

1 Answer

How would I replace my fuel Filter


The fuel filter is an integral component of the fuel pressure regulator, which is mounted on top of the fuel pump module, located in the fuel tank. When the fuel filter/regulator assembly requires service, the fuel tank must be removed from the vehicle, however, the fuel pump module does not need to be removed.
  1. Disconnect the battery ground cable.
  2. You dont have to relieve your fuel systems pressure because your jeep has an automatic bleeder.
  3. Remove the fuel tank assembly.
  4. Clean the area around the fuel filter/regulator.



0900c152800a96ce.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Remove the fuel filter/pressure regulator retaining clip from the top of the assembly


0900c152800a96cf.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the old fuel filter/pressure regulator mounting gasket

  1. Disengage the retaining clamp from the top of the filter/regulator assembly. Discard the retaining clamp.
  2. Using 2 small prying tools, pry the filter/regulator assembly out from the top of the fuel pump module. The filter/regulator assembly will unsnap from the fuel pump module.
  3. Remove and discard the mounting gasket below the filter/regulator.
  4. Before discarding the fuel filter/pressure regulator assembly, inspect the assembly to verify that the O-rings are intact. If the smallest of the 2 O-rings cannot be found on the bottom of the filter/regulator, it may be necessary to remove it from the fuel inlet passage in the fuel pump module.

To install:


0900c152800a96d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Check the condition of the fuel filter/pressure regulator O-rings

  1. Clean the recessed area in the pump module where the filter/regulator assembly is to be installed.
  2. Check the replacement filter/regulator assembly to make sure that the new O-rings are already installed on the assembly.
  3. Apply a small amount of clean engine oil to the O-rings.
  4. Install a new gasket on top of the fuel pump module.
  5. Press the new fuel filter/pressure regulator assembly into the top of the fuel pump module until it snaps into position (a positive click must be heard or felt).
  6. The arrow on top of the fuel pump module should be pointed towards the front of the vehicle (12 O&rsquoclock position).
  7. Turn the filter/regulator assembly until the supply tube (fitting) is pointed to the 11 O&rsquoclock position.
  8. Install new retainer clamp (the clamp snaps over the top of the filter/regulator and locks to the flanges on the pump module).
  9. Install the fuel tank assembly.
  10. Connect the negative battery cable.

Jan 28, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Were is the fuel filter location on this suv. I've look on the frame rails


if it is a 99-04 land rover here are the steps
FUEL FILTER
Service repair no - 19.25.02
Remove
1. Disconnect battery negative lead.
2. Depressurise fuel system. See this section.
3. Raise the vehicle.
WARNING: Support on safety stands.
4. Position container beneath fuel filter to catch spillage.
5. Disconnect fuel hoses from filter.
6. Remove 'O' rings and discard.
7. Remove bolt securing filter and strap assembly.

Remove assembly.

Refit
8. Transfer strap to new fuel filter.
9. Position filter and strap assembly to floor pan. Ensure that flow arrow points toward front of vehicle.
10. Secure filter strap with bolt.
11. Using new 'O' rings, connect fuel hoses to filter. Tighten to 20 Nm (15 lbf.ft)
12. Remove container beneath filter.
13. Remove safety stands. Lower vehicle.
14. Reconnect battery negative lead.

if you can provide me with an exact year and model i will be glad to help you. Thanks, Midwest-tek

Aug 31, 2010 | Land Rover Discovery Cars & Trucks

2 Answers

How do you change a fuel filter


All WJ models have two fuel filters, a strainer filter at the bottom of the fuel pump module inside the fuel tank and one exterior filter within the fuel pressure regulator. Both filters are designed for extended service. They do not require normal scheduled maintenance. Filters should only be replaced if a diagnostic procedure indicates to do so.

The combination fuel filter/pressure regulator is located in front of the fuel tank and above the rear axle. It is transversely mounted to a chassis crossmember (left-to-right). The filter/regulator is equipped with 3 fuel line fittings (2 at one end and 1 at the other end). The single fitting facing the left side of the vehicle is the supply line to the fuel rail. The 2 fittings facing the right side of the vehicle are connected to the fuel tank. Of these 2 fittings, the fitting towards the front is used for fuel return to the fuel tank. The fitting towards the rear is a pressure line.

8bac4de.jpg

Fig.: Fuel filter / regulator location


External filter/regulator removal
WARNING: THE FUEL SYSTEM IS UNDER A CONSTANT PRESSURE (EVEN WITH THE ENGINE OFF). BEFORE SERVICING ANY FUEL SYSTEM HOSES, FITTINGS OR LINES, THE FUEL SYSTEM PRESSURE MUST BE RELEASED.

1. Remove fuel fill cap.
2. Remove fuel pump relay from Power Distribution Center (PDC). For location of relay, refer to label on underside of PDC cover.
3. Start and run engine until it stalls.
4. Attempt restarting engine until it will no longer run.
5. Turn ignition key to OFF position.
6. Disconnect negative battery cable at battery.
7. Raise vehicle.
8. Clean area around 3 filter/regulator fittings.
9. Disconnect fuel supply, fuel return and fuel pressure lines at filter/regulator. Special tools may be required.
10. Remove 2 mounting bolts and remove filter/regulator.



External filter/regulator installation
1. Before installing filter/regulator, be sure all fittings are cleaned of all dirt and contaminants.
2. Be sure o-ring is positioned into fuel return fitting in filter/regulator.
3. Apply a small amount of clean engine oil to o-rings.
4. Position filter/regulator to body and install 2 bolts. Tighten bolts. Refer to Torque Specifications.
5. Connect 3 fittings.
6. Connect negative battery cable to battery.
7. Start engine and check for leaks.


Hope helps (remember rated this).

Jul 05, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Replace fuel filter


The fuel filter is located near the rear of the vehicle, forward or rearward of the fuel tank, depending upon application. There is no service interval for fuel filter replacement. The filter only is replaced if it becomes restricted.

REMOVAL & INSTALLATION Relieve the fuel system pressure at the shrader valve on the fuel rail. For details regarding this procedure, please refer to Fuel System of this information.
  1. If not done already, disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Clean both fuel feed pipe connections and the surrounding areas at the in-line fuel filter with a clean rag to avoid possible contamination of the fuel system.
  4. Using a backup wrench, remove the fuel line fittings from the fuel filter. Most of the models fuel gilter wrench sizes will be 16mm and 20mm.
  5. Either disconnect the quick-connect fittings by pushing inward toward the filter and grasping the plastic tab around the connector and pull them apart. Or remove the fuel filter mounting screws, then remove the filter from the vehicle.
  6. Discard the fuel line O-rings and replace with new ones during installation.
To install:

Install new O-rings to the fuel line fittings.
Connect the fuel lines to the fuel filter.
Position the filter in the same position it was during removal. Using a backup wrench, tighten the fuel lines to 20-22 ft. lbs. (27-30 Nm).
  1. Install the fuel filter mounting screws if used.
  2. Lower the vehicle. Install or tighten the fuel filler cap, then connect the negative battery cable.
  3. Start the engine and check for leaks. Turn the ignition switch to the ON position for two seconds.Turn the ignition to the OFF position for ten seconds. Turn the ignition to the ON position. Check for leaks.
39cf52a.jpg

Jun 07, 2010 | 1992 Oldsmobile Ninety Eight

1 Answer

Where is the fuel filter on a 2000 Mazda Millenia 2.3 V6


Fuel Pump-Mounted Filter
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel pump cover plate
    • Fuel lines from the fuel pump
  4. Raise the fuel pump from the tank.
  5. Remove the fuel filter assembly.
To install:
  1. Install or connect the following:
    • Fuel filter to the fuel pump. Lower the pump assembly into position
    • Fuel lines
    • Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary.
  3. Install the fuel pump cover plate.

Inline Filter
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable

bcd3f99.gif
Exploded view of an in line fuel filter and related components

  • Air intake hose and/or filter housing, if necessary
  • Fuel line clamps, if equipped
  • Fuel lines from the filter and plug the openings
  • Filter clamp bolt/nut by loosening them.
  • Fuel filter from its mounting bracket

  • NOTE Note the direction of the flow arrow on the filter so the replacement filter can be installed in the correct position.


    To install:
    1. Install or connect the following:
      • Fuel filter in its mounting bracket, making sure the flow arrow is pointing in the proper direction
      • Fuel lines to the fuel filter
      • Fuel line clamps, if equipped
      • Air intake hose and/or filter housing, if removed
      • Negative battery cable
    2. Pressurize the fuel system and check all connections for leaks.

    May 24, 2010 | 1998 Mazda Millenia

    1 Answer

    How to replaced fuel filter on ford f250


    Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
    The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
    Removing a Fuel Filter on an EFI Vehicle
    fps23-01.jpg Disconnect the negative cable at the battery.
    fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
    fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
    fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.
    fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
    fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
    fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
    fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.
    fps23-09.jpg Art courtesy of Delmar - Thomson Learning. Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
    Installing Fuel Filters
    In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
    • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
    • Apply a few drops of clean engine oil to the male tube ends on the filter.
    • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
    • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
    • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
    • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
    • Then, do the same with the inlet connector.
    • Now tighten the filter retaining bolt to the specified torque.
    • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter. NOTE THIS IS FOR A 3/4 TON 5.8L

    May 22, 2010 | 1992 Ford F250

    2 Answers

    Where is fuel filter located on 98 sidekick 4dr auto 4wd 4cyl?


    1. Raise the vehicle. Check to make sure the supports are safe and secure. Take a drain pan and several clean shop rags to mop up any spilled fuel.
    2. Crawl under the right side of the vehicle between the front and back wheels. Set the drain pan under the fuel filter to catch any fuel that drains from the lines.
    3. Press the fuel line clamp tabs with a pair of pliers and detach the fuel lines from the fuel filter. Slide the clamp down both fuel lines away from the fuel filter while maintaining pressure on the clamp.
    4. Note the position of the fuel filter inlet and outlet nipples before removing the fuel filter. Remove the lower clamp bolt and loosen the clamp adjusting bolt. Remove the filter from the mounting clamp. Lift the fuel filter out of the mounting clamp.
    Install the Fuel Filter:
    1. Work under the vehicle. Slide the new filter into its mounting clamp. Tighten the adjusting bolt until it's snug. Turn the filter in the clamp so that the inlet and outlet nipples are in the same position as before removal. Tighten the adjusting bolt. Put the lower clamp bolt in position. Tighten it securely.
    2. Connect the outlet hose to the top filter nipple. Connect the inlet hose to the lower nipple. Push the fuel lines up over the nipples as far as possible. Compress the fuel line clamp tabs and slide the clamp up each line until it is secure over the nipple.
    3. Position the clamps at least 1/4 inch from the connected end of the fuel lines, making sure the clamps are set over the nipples. Start the engine and allow it to idle. Check for fuel leaks and make the necessary adjustments. Turn the engine off. Lower the vehicle.
    Oh and if you missed it, filter is attached with a bracket to a crossmember in front of the fuel tank on the passenger side.
    Thank you for using fixya and be safe.



    Apr 10, 2010 | 1998 Suzuki Sidekick

    1 Answer

    Replace fuel filter


    1. Relieve the fuel system pressure. For details regarding this procedure, please refer to Section 5 of this manual.
    2. If not done already, disconnect the negative battery cable.
    3. Raise and safely support the vehicle.
    4. Clean both fuel feed pipe connections and the surrounding areas at the in-line fuel filter with a clean rag to avoid possible contamination of the fuel system.
    5. Using a backup wrench, remove the fuel line fittings from the fuel filter.
    6. Either separate the quick-connect fittings or remove the fuel filter mounting screws, then slide the fuel filter out of the mounting bracket.
    7. Discard the fuel line O-rings and replace with new ones during installation.
    To install:
    1. Install new O-rings to the fuel line fittings.
    2. Connect the fuel lines to the fuel filter.
    3. Position the filter in the mounting bracket, in the same position it was during removal. Using a backup wrench, tighten the fuel lines to 16 ft. lbs. (22 Nm).
    4. Install the fuel filter mounting screws.
    5. Carefully lower the vehicle. Install or tighten the fuel filler cap.
    6. Connect the negative battery cable.
    7. Start the engine and check for leaks.
    25d7525.gif
    Location of the fuel filter

    9f0ac98.gif
    Unfasten the retaining bracket can make removal of the fuel filter easier

    2c6ca73.gif
    Either use a clean rag or compressed air to clean the surrounding areas of the filter

    523254f.gif
    Use a backup wrench to disconnect the fuel line fittings from the filter

    2e1fdd8.gif
    Disengage the quick-connect fittings, then remove the filter from the vehicle

    0d20d1f.gif
    In-line fuel filter mounting and related components

    It sits in front of the fuel tank.

    Dec 07, 2009 | 1992 Buick Riviera

    2 Answers

    1999 jeep cherokee do you have to remove the fuel pump to replace


    The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

    The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

    REMOVAL
    1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
    2. Clean area around filter/regulator.
    3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
    5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
    6. Discard gasket below filter/regulator.
      1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
      INSTALLATION
      1. Clean recessed area in pump module where filter/regulator is to be installed.
      2. Obtain new filter/regulator (two new O-rings should already be installed)
      3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
      4. Install new gasket to top of fuel pump module.
      5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
      6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
      7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
      8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
      9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
      10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
    WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

    Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

    The quickest draining procedure involves lowering the fuel tank.

    As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

    If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

    FUEL TANK REMOVAL
    1. Disconnect negative battery cable at battery.
    2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
    3. Raise and support vehicle.
    4. If Equipped: Remove fuel tank skid plate.
    5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
      1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
      2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
      3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
        1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
        2. Disconnect EVAP canister vent line near front of tank.
        3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
          1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
          2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
          3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
            1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
            2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
            INSTALLATION
            1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
            2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
            3. Install hose clamps to hoses. Position clamps between index marks on each hose.
            4. Position fuel tank to hydraulic jack.
            5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
            6. Continue raising tank until positioned to body.
            7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
            8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
            9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
            10. Connect fuel pump module pigtail harness electrical connector near front of tank.
            11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
            12. Connect EVAP hose near front of tank.
            13. Install exhaust tailpipe heat shield.
            1. Install fuel tank skid plate (if equipped).
            1. Lower vehicle and connect battery cable to battery.

    Feb 08, 2009 | 1999 Jeep Cherokee

    Not finding what you are looking for?
    2011 Chevrolet Cruze Logo

    Related Topics:

    155 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...