Question about Jeep Cars & Trucks

1 Answer

The Camaro part is $30. the jeep part is $110.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Id buy the Yugo part, it beats them all.

Posted on Apr 30, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers don't work and I found a 4.8A 12v 4GA 8956 001 110 fuse like part on the floor under steering wheel


I had the same thing happen to me.

The piece you found is dealer part # 56001110 and is a 4.8 amp breaker that controls the windshield wipers.
It plugs into the bottom of the fuse panel, a little above where your left foot rests when driving the car.

I was wearing my size 14 boots and kicked it out, which snapped off the two tabs.
I pulled the tabs out of the box with pliers then bought a replacement.
I read that the dealer sells them for about $30 and some websites (like Quadratec, part # 17015.8000) sell them for about $30 as well, but I bought one on eBay for a few bucks cheaper.

That fuse panel is in a bad location.

Oct 09, 2012 | 1995 Jeep Cherokee

1 Answer

Head bolt sequence and tourqe for 99 jeep 4.0 motor


  1. CAUTION
  2. During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  3. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  4. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  5. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  6. Tighten bolts in sequence:
  7. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  8. Bolt 11 to 100 ft. lbs. (135 Nm).
  9. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  10. Check all bolts in sequence to verify the correct torque.


ledsled378_134.jpg

Jul 02, 2011 | Jeep Cherokee Cars & Trucks

2 Answers

Dear expert What are the cylinder head bolt torque settings for the 4.0L MFI straight 6 engine? Regards Dave


Here are the specs and sequence:

0900c152800a9943.gif

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

  1. Tighten all bolts to 22 ft. lbs. (30 Nm).
  2. Tighten all bolts to 45 ft. lbs. (61 Nm).
  3. Retighten all bolts to 45 ft. lbs. (61 Nm).
  4. Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
  5. Tighten bolt 11 to 100 ft. lbs. (136 Nm)
  6. Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)

May 04, 2011 | 1996 Jeep Grand Cherokee

1 Answer

I am looking for the head bolt torque specifications and sequence for a 1988 jeep Cherokee 4.0 i6


zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Mar 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

What is the head bolt torque specs on a 1990 jeep 4.0


  1. Tighten all bolts in sequence (1 through 14) to 30 N·m (22 ft. lbs.) torque.
  2. Tighten all bolts in sequence (1 through 14) to 61 N·m (45 ft. lbs.) torque.
  3. Check all bolts to verify they are set to 61 N·m (45 ft. lbs.) torque.
    1. Tighten bolts in sequence:
    2. Bolts 1 through 10 to 149 N·m (110 ft. lbs.) torque.
    • Bolt 11 to 135 N·m (100 ft. lbs.) torque.
    • Bolts 12 through 14 to 149 N·m (110 ft. lbs.) torque
  • 900c8cad.gif

    Dec 16, 2010 | 1990 Jeep Cherokee Limited

    1 Answer

    I would like to know if there is a way i can take off the speed limiter on my 2005 v6 mustang


    what are you saying the car only will go a certain speed and that's it? I owned a 1989 Ir oc camaro that would only go 110 miles per hour then the engine would loose power and wouldn't go any faster than 110. I had to replace the computer chip in it them i got about 145 out of it. but was to scared to go any faster.

    Sep 13, 2010 | Ford Mustang Cars & Trucks

    1 Answer

    Head bolt tighting sequance for a jeep 4.0


    CAUTION: During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT overtighten bolt No.11.

    • Tighten all bolts in sequence (1 through 14) to 30 Nm (22 ft. lbs.) torque.
    • Tighten all bolts in sequence (1 through 14) to 61 Nm (45 ft. lbs.) torque.
    • Check all bolts to verify they are set to 61 Nm (45 ft. lbs.) torque.
    • Tighten bolts in sequence:
    • Bolts l through 10 to 149 Nm (110 ft. lbs.) torque.
    • Bolt 11 to 13 Nm (100 ft. lbs.) torque.
    • Bolts 12 through 14 to 149 Nm (110 ft. lbs.) .
    • 21e690f.gif

    Apr 21, 2010 | 1998 Jeep Cherokee

    1 Answer

    What is the cylinder head torque on a 2001 jeep cherokee


    Please don't forget to rate....thanks:


    e1aba13.gif

    1. Tighten the engine cylinder head bolts in sequence according to the following procedure

      CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

    2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
    3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
    4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
    5. Tighten bolts in sequence:
    6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
    7. Bolt 11 to 100 ft. lbs. (135 Nm).
    8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
    9. Check all bolts in sequence to verify the correct torque.

    Mar 06, 2010 | 2001 Jeep Cherokee

    1 Answer

    Security on 96 camaro


    try this, turn key on and walk away for 30 mins, after 30 mins turn key off, wait 15 secs, the try starting, this should reset the anti-theft system

    Jul 09, 2009 | 1996 Chevrolet Camaro

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    24 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...