Question about Chevrolet Cars & Trucks

Open Question

89 Chevrolet s-10 2.5 liter flashes brake light 7 times

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 57 Answers

SOURCE: Chevrolet Equinox Brake Light Flashing

If it is an amber light that says " anti lock" You will be safe, you just wont have anti lock brakes. The car may have traction controll. If so, look in the manual to be sure what light is on. As a general rule amber lights are warnings and red lights means stop. If the light stays on you will have to go to the dealer to have the code read.

Posted on May 19, 2009

Ad
  • 32 Answers

SOURCE: my parking break light flashes 6 short, 1 long and

6 short flashes seperated by one long flash indicates an erratic speed signal with the rear wheel antilock system. after performing any repairs, with key turned off, pull the stop/hazard fuse for 5 seconds to clear codes. the speed sensor is located towards the rear of the transmission on the driver's side

Posted on Jun 20, 2009

dmftrucker
  • 1922 Answers

SOURCE: Describe your 2001 Chevrolet S-10 Prowhere is the

fuse panel is either on the fire wall inside vehicle behind park brake and brake pedal or horizontally right near there looking up by brake pedal,also try and see if brake switch behind brake pedal is adjisted properly you can see this switch and the plunger on switch at brake pedal in the same location

Posted on Jul 10, 2009

bschilz
  • 2049 Answers

SOURCE: why do the brake lights stay on my 89 chevrolet

Sounds like your brake light switch, which is behind the brake pedal, may have failed. They are simple and inexpensive to replace.

It looks like a bracket, that wraps around the brake pedal arm, and it has a cylinder type switch that makes contact with the brake pedal arm. When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on.

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Resetting 1999 cavalier security system


If it's a factory alarm then you need to get it disabled by the dealer. if it's an installed alarm you need to unplug the brain/ module and your car should run

Feb 25, 2013 | 2001 Chevrolet Cavalier

2 Answers

1989 s-10 2.5 liter,when engine starts,the spark plugs become "fuel fouled"what causes this?


air filter really dirty, injectors stuck open. fuel pressure regulator is bad.

Feb 12, 2011 | 1988 Chevrolet S-10

1 Answer

How do you reset the brake light on a 89 s-10 blazer? I tried pulling up on the parking brake while releasing it and the dash light stays on steady.


this light will also come on if you are low on brake fluid if its low top it off a little but this is also an indicator of a leak or brake wear from there check the switch when the pedel hits it for adjustment and whether it is workin properly

Jul 25, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Hello, I have an 89 ford bronco II with a 2.9


Could be that you have one or more brake lines rotting internally and plugging the line. Check for a soft spot in the brake lines.

Jul 04, 2010 | 1989 Ford Ranger

2 Answers

89 s10 has a high idle


Adjust the idle though the throttle body at the top

Apr 16, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

Park brake light flashes 10 times. For 1989 Chevy 1500 pickup. What does this mean?


This truck probably has Rear Wheel Anti-Lock (RWAL) brakes. There is a small black module near master cylinder that is the brain for this system. There are ways to check for diagnostic trouble codes in this system. Once you have any codes set, diagnosis can be fairly simple. PROCEDURE:
Diagnostic Trouble Codes (DTC) 's can be displayed by jumping terminals "A" and "H" of the Data Link Connector and observing the flashing of the "BRAKE" warning light. This should only be done when the brake lamp is "ON".
The terminals must be jumped for about 20 seconds before the code will begin to flash. Count the number of short flashes starting from the long flash. Include the long flash as a count. Sometimes the first count sequence will be short. However, subsequent flashes will be accurate. If there is more than one failure, only the first recognized code will be retained and flashed.

NOTES:
DTC's 6, 9 and 10 will only turn the "BRAKE" lamp on while the fault exists. These are soft codes faults and can only be read with the Tech 1 scan tool.
Do not jump terminals "A" to "H" if the "BRAKE" lamp is not on. Jumping the terminals with the "BRAKE" lamp off will set a false DTC 9. This will turn the "BRAKE" lamp on and disable the antilock system.

d09165f.gif
  • 1, 11, & 12 ECU Malfunction
  • 2 Open Isolation Valve or Malfunctioning ECU
  • 3 Open Dump Valve or ECU Malfunction
  • 4 Grounded Antilock Valve Reset Switch
  • 5 Eccessive Actuations of the Dump Valve
  • 6 Erratic Speed Signal
  • 7 Shorted Isolation Valve or Faulty ECU
  • 8 Shorted Dump Valve or Faulty ECU
  • 9 Open Circuit to Speed Signal
  • 10 Brake Lamp Switch Circuit
  • 13, 14 and 15 ECU Malfunction
  • Sep 29, 2009 | 1989 Chevrolet C1500

    1 Answer

    The e-brake light on the dash of my '89 Chev blazer S-10 blinks.


    If you have Anti-Lock Brakes, have them checked. Otherwise it is most likely your master cylinder, check the fluid level, and if it is fine you will need to replace it. Your pedal feel may not feel diminished, but it will definitely need to be replaced soon... of course if its not an ABS issue. If you do replace your master cylinder, follow the instructions and most certainly bench bleed it. It could be catastrophic with out it.

    May 27, 2009 | 1989 Chevrolet S-10 Blazer

    1 Answer

    The turn signals don't work in the rear of my 1991chevy s-10.


    Hello, I see you are having problems with you turn signal and brake lights on a 91 s10. If you will try switching the hazzard flasher off and on several times and shaking the turn signal left turn to right turn several times that may get the signals and brake to working again. The are probably just not making good connections inside. Thank You.

    Feb 23, 2009 | 1991 Chevrolet S-10

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...