Question about Cars & Trucks

1 Answer

Looking for a 1928 6 cyl. engine specs & tuning info

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,657 Answers

Is this really a 1928 vehicle? Is it a US manufactured vehicle? What is make and model?

Posted on Apr 29, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Lower intake torque spec for 2005 cyrysler pacifica

1st stage 9 ftlbs
2nd stage 21 ft lbs
Note the torque sequence. This info is for 3.8L engine. The torque specs came from autodata tune-up cd, it has a lot of torque specs for different makes--models--years. If somebody has info from a better database, please jump in. All databases are not created equal.

Nov 06, 2016 | Cars & Trucks

1 Answer

What size is my engine with the serial no ending in xtd

Type your VIN number using the website below and it will decode it for you. Typically the eighth digit of the VIN is the engine code.

You can also look under the hood for the emisisions sticker on most vehicles built after the 70's. It will have basic info like the production date, tune-up specs, vacuum diagrams and and engine size.

Jan 25, 2016 | Cars & Trucks

1 Answer

What are the toyota torque specifications

It all depends on the year, best info is to call your local machine shop or check with your local parts stores to see if they have a Chilton or Haynes repair Manual on hand that has already been opened. If it has you can look inside and get the correct info. Hope this helps

Jul 16, 2014 | Toyota Highlander Cars & Trucks

1 Answer

What are the torque specs for a 1928 caterpillar twenty crawler

got a link to a forum , it may have more info , i'm not into industrial sized monsters , no offence

Jun 08, 2014 | Cars & Trucks

1 Answer

How to change coils on 2003 expedition

please tell me in this tune up you had new spark plugs put in? if check engine light is on there are some stored codes those will give you the suspect cylinder(s) check to see if you have plug wires if not there will be a coil for each cyl. pass. side of motor starting in the front working to the back or firewall cyls are 1,2,3,4 driver side same front to back 5,6,7,8 codes will be PO301 cyl 1. PO302 cyl 2. etc. get the code find the correct cyl. unplug little connector u will need a 7mm socket to remove the bolt holding the coil in place then pull up on the coil and boot.... if u have plug wires get the code find correct cyl and follow plug wire to coil pack in front of engine there will be two one on each side in front of engine...

Apr 17, 2013 | 2003 Ford Expedition

1 Answer

1990 Isuzu Trooper Flywheel needs to be resurfaced what should the step or the depth of the cup be? 2.6 Liter Engine 4Ze1

The Isuzu Amigo 2.6L 4 cyl , The Isuzu Trooper 2.6L 4 Cyl and the Honda Passport I believe with a 2.6L all have the same 4ZE1 2.6L 4 Cyl engine in them.

As per this page =>, found it looking for the same flywheel "cup" (aka we all call it a "step" but the machinists have a different flywheel that they call stepped so the one attached to the 4ZE1 is "Cupped") . Says the cut spec is .157"-.159" , so in this case the clutch pressure plate bolting surface is .157"-.159" higher then the center flat friction surface that the clutch disc sits in. (it doesn't indicate that it's inches or mm but I assume that because most usa machine shops use thousands of an inch calipers and micrometers it's more then likely inches).

Hope that helps you or anyone out there who needed that info :] .

Nov 28, 2010 | 1990 Isuzu Trooper

1 Answer

Six cyl timing spec.s for 1951 big block 6 cly engine.

Sorry, but need a little more info to help you...make of the it the original 6 cylinder? What's it in?

May 28, 2010 | 1991 Ford F150

1 Answer

Need torque specs for rod bearing caps on 1995 toyota terel 4 cyl

1.6 engine 36 ft lbs 1.8 engine 36 ft lbs 2.0 engine 49 ft lbs

Apr 11, 2009 | 1995 Toyota Tercel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides