Question about Cars & Trucks

1 Answer

How do I change a broken bulb? - Cars & Trucks

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,326 Answers

Careful grab bulb at base and pull it out. If need to easily grab inner part with Plyer and pull it out

Posted on Apr 29, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2011 nissan sentra driverside lights keeps going out after bulb was changed

Hi Suzanne:
You did not tell us if the bulb filaments are broken (burnt out, no continuity) or if they are just not turning on.
If the filaments are broken either there is too much voltage (very unusual) or the bulbs may be loose in that particular socket and vibration is hurting them.
If the filaments are OK then you will have a wiring problem, probably corrosion on the bulb terminals or a bad ground.
Hope this helps.

Feb 10, 2016 | Nissan Cars & Trucks

1 Answer

My reverse lights don't work, changed bulb and checked fuse but still not working

It could be the switch at the reverse gear is burnt out or you have a broken wire somewhere. The broken wire situation is not fun to solve. You'll need to pinpoint if you are getting power the length of the wire harness.

Jan 31, 2015 | Cars & Trucks

1 Answer

Why does my blinkers on 93 c2500 blink fast all bulbs work

check bulbs are correct for application,check for loose -broken ground

Mar 04, 2013 | 1993 Chevrolet C2500

2 Answers

Roof light stopped working

Fuses do not cause bulbs to burn out. You probably have a defective light fixture.

May 28, 2012 | Cars & Trucks

1 Answer

Low beam right light not working and fuse is ok

sounds simple but check there is live at the bulb with a multimeter or 12v test light. should show round 12v. if not then it will be a wiring fault/broken circuit or bad earth. if there is then check the bulb connections and change try changing bulb even if you feel it may look ok. looks can be decieving

Apr 29, 2012 | 2003 Nissan Altima

3 Answers

Right brake light out changed bulb and fuse still wont work

Check the brake switch located above the brake pedal. It may be shorted or faulty. Check the wiring to make sure that it is not broken anywhere.

Sep 29, 2010 | 1997 Land Rover Discovery

2 Answers

Tail lights do not work all lights work but the back lights do not work. I change the fuse but lights still don't come on. all the other lights work is there other fuses i need to replace

if the bulbs are ok! check bulb socket to see if you have power.with test light, if not make sure sockets are clean. check the bulbs first, because they are a double filiment bulb. for brakes and tail lights. did you change the correct fuse!! it is located in interior fuse box on drivers side end of dash. its on bottom left side of fuse box. its labled "stp lps". hope this helps,

Aug 13, 2010 | 2000 Chevrolet Malibu

1 Answer

1998 pontiac transport/montana has not tail or break lights...turn signals blink fast or not at all. changed rear bulbs and noticed carbon on front build up on front bulbs. Help!

If one of the filaments in the bulbs is burned out, the remaining working lights will flash alot quicker.
Check the bulbs, and replace if the filaments are broken.
If the front bulb has a carbon build up it blown out...change it..
Once the bulbs are replaced your signals should work properly.

Dec 09, 2009 | Pontiac Trans Sport Cars & Trucks

1 Answer

BRAKE LIGHTS OUT REVERSE LIGHTS OUT , all fuse and bulbs look ok

First try to change the fuses, then check the wiring connectors if you get power or not. If not, check the wiring back from the bulbs to front of the car. best case is to have a broken wire between the bulbs and the wiring near driver seat floor. Worst case: you have a broken wire under the dashboard. Questions? Come back again please.

Oct 27, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides