Question about 2011 GMC Terrain

2 Answers

Diagnostics showed codes P2714 and P0700. My dealership said the transmission must come out and wants to charge me $1500.00 and that doesn't even cover parts! I just purchased my 2011 G M C Terrain

Posted by on

2 Answers

This could just be a faulty linkage ... be warned

Posted on Apr 29, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 1,326 Answers

I looked the codes up doesn't look like much else can be done except to rebuild transmission. I would however check into getting a price from aamco the dealer charges more. I would get a good used one from a reliable source

Posted on Apr 29, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Tnsiouxfalls
  • 617 Answers

SOURCE: I have trouble codes P0700 (transmission control

P1192 Post-catalyst Fuel Trim System Bank 1 Check your Oxygen Sensor Heater Circuit, could be dirty or loose wires or just stop working. Usually you have 4 of these under your car so check all. Fault Code P0700


Message:
Here's what my service manual says:

EATX Controller DTC Present

This SBEC III or JTEC DTC indicates that the EATX or Aisin controller has an active fault and has illuminated the MIL via a CCD (EATX) or SCI (Aisin) message. The spscific fault must be acquired from the EATX via CCD or from the Aisin via ISO-9141.

Here's what I know: MIL=malfunction indicator light; DTC=diganostic trouble code; CCD=Chrysler collision detection. Beyond that, I'm clueless. Sounds like it needs to be read out at the dealer. Then again, if it was a one-time glitch, it might clear itself after several drive cycles.

Posted on Feb 18, 2010

  • 235 Answers

SOURCE: I am having a electrical problem with my 2009

Have they replaced the altenator? If so and problem still persists then it is the voltage regulator or maybe a short in the wiring. I believe it is a damn shame that they don't make good on the battery after they keep replacing it . If they don't want to replace the altenator or regulator or search for shorts get a lawyer.

Posted on Dec 04, 2010

shinehutt
  • 254 Answers

SOURCE: Blasting cold air on the

the vent system uses flaps and seros to control air flow if you get good heat on other settings a door or servo is not working

Posted on Jan 10, 2011

SOURCE: p0014 fault code . exhaust

www.engine-light-help.com/generic-check-engine-light-codes.html

Posted on Mar 25, 2011

ginko
  • 19396 Answers

SOURCE: engine light came on in

Hi.

Please click here and read the article I posted about P1775, P0700 is consequence of the first code.

Regards.

Ginko.

Posted on May 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is my transmission bad or going bad soon since i have code p0700


P0700 is code for trans control malfunction. It does not indicate the condition of your transmission. Check the fluid level. If it is low, it causes problems. Otherwise, it will require more diagnostics.
It could be a bad electrical connection. It could be worse.
Good luck.

Oct 10, 2014 | Cars & Trucks

1 Answer

1997 honda accord tranmission problem code p0700 drive 4 flashes


Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.

Symptoms Symptoms of a P0700 DTC may include:
  • Malfunction Indicator Lamp (MIL) illumination
  • The transmission may exhibit drivability problems like slipping, etc.
Causes More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
Possible Solutions For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.
If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.

Oct 20, 2012 | 1997 Honda Accord

1 Answer

Check engine light is on code 700


Hi there:
DTC P0700 - Transmission Control System Malfunction
Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.

This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.

Symptoms of a P0700 DTC may include:
Malfunction Indicator Lamp (MIL) illumination
The transmission may exhibit drivability problems like slipping, etc.

More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).

Possible Solutions: For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.

If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 30, 2012 | 2006 Hyundai Sonata

1 Answer

P0700


Hi there:Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.
More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.

Mar 02, 2012 | 1996 Chevrolet Blazer

1 Answer

What is the code p1684 and p700


The P1684 code means simply that the battery has been disconnected within the last 50 starts, You can effectively disregard this unless you know that to be false. Then it could be an indication of an impending battery failure.The P0700 code is more troublesome. I collected this information from another source:

What does that mean? Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults. If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.
This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.

Symptoms Symptoms of a P0700 DTC may include:
  • Malfunction Indicator Lamp (MIL) illumination
  • The transmission may exhibit drivability problems like slipping, etc.
Causes More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).
Possible Solutions For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.
If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.

Hope this helps!

Jan 07, 2012 | Dodge Grand Caravan Cars & Trucks

2 Answers

Obd2 p0700


Hi John:
DTC P0700 - Transmission Control System Malfunction
Many vehicles have a control module for the automatic transmission called a transmission control module (TCM). The engine control module (ECM) communicates with the TCM to monitor the automatic transmission for faults.

If the TCM detects a fault in the automatic transmission and sets a transmission related fault code, the ECM is informed of this also and sets a P0700 in the ECM memory.

This illuminates the Malfunction Indicator Lamp (MIL) to let the driver know there is a problem. If this code is present and the MIL (Malfunction Indicator Lamp) is illuminated that basically means there is at least one transmission code set in the TCM's memory. P0700 is an informational code only. It doesn't point to a direct fault in the engine, only a general fault in the transmission. More diagnosis is necessary to identify what the transmission fault is. This requires a scan tool that will communicate with the transmission module.

Symptoms of a P0700 DTC may include:
Malfunction Indicator Lamp (MIL) illumination
The transmission may exhibit drivability problems like slipping, etc.

More often then not, the cause of this code is that there is a transmission problem of some kind. The TCM detected the problem and set a code. P0700 means that a fault code is stored in the TCM. However this doesn't rule out the possibility of a failed PCM or TCM (unlikely).

Possible Solutions:
For a P0700 the only real solution is to acquire a scan tool that will communicate with the transmission control module. Extracting this code from the TCM will be the first step in repairing the fault in the transmission.

If the TCM compatible scan tool will not communicate with the Transmission Control Module then that is a good indication that there may be a fault with the TCM itself.

Fee free to contact us if need additional details. Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 06, 2011 | 2001 Daewoo Leganza

1 Answer

2006 tribeca subaru b9 p0700 and p1844 code pops up when I plug in the diagnostics unit. what do they mean?


both codes are related.

code P0700 transmission control system

code P1844 transmission fluid pressure sensor.

most likely cause is a bad transmission fluid pressure sensor this sensor will set both codes. have someone with a scanner rad the info from the sensor it is most likely open or shorted...best guess replace the sensor.

Sep 30, 2011 | 2006 Subaru B9 Tribeca

1 Answer

P0700 Transmission Control System Malfunction came up how is it fixed


THIS IS A DEALERSHIP FIX.CODE MEAN TRANSMISSION CONTROL MODULE REQUESTED MIL ILLUMINATION.IF YOU HAVE PROBLEM WITH TRANSMISSION MODULE IF REPLACED IT HAS TO BE REPROGRAM BY THE DEALERSHIP.

May 17, 2010 | 2003 Saturn L-Series

Not finding what you are looking for?
2011 GMC Terrain Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...