Question about Cars & Trucks

2 Answers

I need an o ring & rubber ring that makes it pump up & the round pin that hold it in.

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 352 Answers

Look for it at rock auto RockAuto Parts Catalog . They have all the after market parts and most of the parts a dealer carries. Price is right too.

Posted on Apr 28, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 90 Answers

Go to your local auto part store they should have what you are looking for.

Posted on Apr 28, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I need an O ring for the gas tank

Make sure that you get an o ring with rubber composition impervious to gasolene.

Jun 12, 2017 | Cars & Trucks

1 Answer

Replace fuel pump chevy

The fuel pump is inside the fuel sending unit. The sending unit is mounted on the topside of the fuel tank. There is a large O-ring that seal the sending unit to the tank (so gas does not leak out). This is a tedious job and requires the tank to be dropped. if the tank is full, the task of dropping the tank will be more dangerous. The fuel filler hose, fuel vapor hose, fuel supply line, fuel return line, and the electrical harness will need to be disconnected before you release both tank support straps. ***NOTE: the two fuel-lines coming off the sending unit are well designed to make them easy to remove. Personaly this design is one of my favorites. No special tools are needed to release the connections.***After the tank is slowly lowered onto the floor then you can start removing the sending unit. There is a round metal ring with four securing tabs. You will see a light blue plastic pin. This pin must be pulled/removed before the metal ring can be removed. NOTE: make sure your work area is clean, free of trip hazards, and no sparks or open flames. After the metal ring is removed, then the sending unit can be pulled out and replaced.

Jan 10, 2014 | 2004 Chevrolet Malibu

2 Answers

Ring holding fuel pump in tank is corroded / rusty. Can't move it, are the tabs secured with slots OR by turning the ring will the slots move and tabs stay put??

I remove them with a flat punch and a ball pean hammer gently tap on the ring away from the stops and the ring will rotate off

May 12, 2011 | 2001 GMC Jimmy

1 Answer

How to change fuel pump on 1995 f-350

The fuel pump is in the tank. Lower the gas tank and unhook all the lines. On the top there should be a big round disk holding the sending unit down use a hammer or dead blow hammer and a punch to knock it counter clockwise. The sending unit should pop up, save the rubber o-ring that is under it as you will reuse it unless the new one has one. Pull the sending unit out of the tank and yout pump will be on it. I believe on those ones you have to reach into the tank and pinch 2 clips on the sides to get the pump out of the tank. Reverse order to reinstall. Make sure ring on top is all the way back on before putting tank back in place. I usually get someone to help with the hold down ring and we both use a dead blow and punch from each side to knock it back into place

Dec 01, 2010 | 1995 Ford F350

2 Answers

Where does rubber ring ,gasket go on the fuel pump instalation?

It goes in the groove under the fuel pump module top plate in the top of the fuel tank round opening

Nov 21, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Where is the fuel tank located in a 1991 buick park ave?

Gas tank is located inside of fuel tank. Loosen the two straps on tank and let the tank drop slowely with floor and wood support underneath.(make sure gas is removed so it is not so heavy) Lower tank and remove electrical wire connections and remove filler hose from tank side.Remove tank from car. Tank has round o ring lock on top.Take rubber malet and tap o ring counter clockwise to remove pump assembly replace pump and then use reverse procedre to put tank back.Good luck.

Aug 20, 2010 | 1991 Buick Park Avenue

2 Answers

How do i take my fuel pump out in my bmw 325, i got the rear seat put and the cover on the passenger seat off, i just cant get the pump out

The fuel pump in your 325 is under the rear seat, passenger side. Take the seat out, then pull up the rubber grommet with the wire going through it. Leave the wire alone for now. Peel up the thin rubber insulating mat. It is pre cut by the factory and not glued down. Remove the four nuts (10mm socket) and lift the round plate. Now remove the wire by sliding the plastic plug type housing back and lift the entire plug type housing up. Now, remove the hose clamp and slide the hose back off the plastic tube. If you damage the clamp, buy a new 1/4" clamp at the auto store for .30cents. Now unscrew the steel ring holding the pump in place. Unscrew this ring by tapping the ring with a screw driver and hammer. Remember counterclockwise (off). Now put your finger in the plastic ring molded into the top of the pump and pull up with some force. It is in place with a rubber gasket. Tight, but it will come loose. Be careful not to drop any thing into the tank. On the other side (drivers side) is a float/sensor. When reinstalling, seat the rubber gasket into the hole then drop the new pump/sensor into place. Your tank is like a saddle bag so it has two float/sensors. Time: 25 minutes

Oct 19, 2009 | 2005 BMW 3 Series

1 Answer

I need advice on installing a new fuel pump 1992 Isuzu Rodeo

fuel tank has to be removed to remove fuel pump sender unit. make sure tank is near empty so its not as heavy to remove
some models have two round rings on top of tank, one is sender unit (for gauge) the other incorporates the fuel pump
others have one round ring which is both in one
remove the one near middle section of tank
be carefull not to bend float arm for sender unit if twin type (sender & fuel pump in one)

Jul 02, 2009 | Isuzu Rodeo Cars & Trucks

1 Answer

How to remove fuel pump from tank s type jag 2002

Fuel pump is accessed through a hole below the back seat. Remove the seat and there is a rubber round cover over each fuel pump. Fuel pumps are held in place with a large round retaining ring that is screwed off.

Dec 01, 2008 | 2002 Jaguar S-Type

2 Answers

How to fit a fuel pump

location of fuel filter on ford au series 2 ute 2000 model

Sep 03, 2008 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14512 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides