Question about Isuzu Cars & Trucks

1 Answer

How do u disconnect a cv axel from the transmission of a 1997 Isuzu rodeo

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 80 Answers

What you should do is purchase a book on Isuzu rodeos at your local auto part store and the answer should be there for you

Posted on Apr 28, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: how to change oil transmission isuzu rodeo 2003

There are two drain plugs on the bottom of the pan. remove the lower one to drain the trans fluid. To refill, use a pump and pump the fluid into the upper drain plug until it seeps out and re-install the plug, similar to refilling a manual trans.
Once this is done, Start the vehicle and run it for about 3 minutes, shifting through all gears (do not drive vehicle Remove the upper drain plug and let any excess fluid drain out. Done. This is as per Mitchell OnDemand.

Posted on Aug 14, 2008

  • 1 Answer

SOURCE: how to check transmission fluid on 2001 isuzu rodeo

There is no dipstick on your auto trans. Checking it is a real PITA The trans pan has 2 plugs in it. The one on the very bottom is the drain. The one in the corner, up higher in a recess is the check/fill plug. To check, the engine must be warm and running, tranny in P. Remove the plug and fluid should dribble out. If it doesn't it's low, fill until it dribbles out, while engine is running. Obviously the truck must be on a lift or up on jackstands.

Posted on Dec 22, 2008

  • 13 Answers

SOURCE: 1997 Isuzu Rodeo

on the side of the block on the passenger side....u can see it through the wheel well

Posted on Feb 15, 2009

  • 41 Answers

SOURCE: removing a drive axle from

if you already have the ball joint dissconnect and the axle out of the steering knuckle just pry out the axle at the transaxle assembly. if it doesnt wont to come out try pushing it in and pry it out vary qiuck pull on the pry bar but they are only held in place with a colasable c-clip just giver.it will come dont worry it wont break

Posted on Mar 22, 2009

  • 1596 Answers

SOURCE: how to replace front cv shafts on a 1997 isuzu

rejakwilson @ aol.com For Full Illistrations (PICTURES) PREPARATIONS:

  1. Jack up the vehicle and support it using jack stands.
  2. Remove the tire and wheel.
  3. Remove the drain bolt to drain differential oil.


NOTE:
  • During the work, be sure that the differential case is supported by the jack.
  • Remove the brake caliper fixing bolt and hang the caliper.
  • Remove the antilock brake system speed sensor. (If equipped with antilock brake system)
  1. Hub assembly (Disc, back plate and knuckle):
    1. Remove the locking hub.
    2. Disconnect the knuckle and the suspension arm.
  1. Steering link and arm assembly.
  2. Suspension crossmember.
  3. Propeller shaft.
  4. Protector.
  5. Breather Hose:
    1. Remove the hose clips.
    2. Disconnect breather hoses from front drive axle tube and disconnect housing.
  1. Vacuum Hose. Disconnect vacuum hose from actuator. Shift switch connector (7a).
  2. VSV Assembly. NOTE: Be sure not to remove hose and connector from VSV assembly.
  3. Mounting bolt and nut.
  4. Washer and spacer.
  5. Bolt. Remove the mounting bracket fixing bolt.
  6. Front axle case assembly and front drive shaft assembly (LH side). Lower the vehicle and disconnect the RH front drive shaft assembly, and then remove the front axle case assembly and front drive shaft assembly (LH).
  7. Front drive shaft assembly (RH).

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the CV axle for a 1998 Isuzu rodeo


THERE ARE PLENTY AVAILABLE FROM SCRAP YARDS, AND E-BAY. THE RODEO HAD PROBLEMS WITH THE TRANSMISSION.

Jun 20, 2015 | 1998 Isuzu Rodeo

1 Answer

1997 isuzu rodeo transmission valve body ball bearing location


that will take a real isuzu full transmission FSM book.
or from the true maker, see that tag on the tranny?
it answer that. on most cars.
will say like Aisin mfg company model x. or ????????

there are 2 choices.

Mar 23, 2015 | 1997 Isuzu Rodeo

1 Answer

Remove cv shaft front left side


Take wheel off then there should be a cover in the center Allen head bolts remove it I think there's a clip to remove and some other spacers then in bolt the lower ball joint pop it loose should be able to push and pull the cv axel out

Apr 20, 2014 | 2001 Isuzu Rodeo

2 Answers

How do i drain the radiator on 1997 rodeo i don't see the drain plug


If this is a 1997 Isuzu Rodeo with a 3.2L engine, this is where the drain plug is. You will have 2 transmission coolant lines attached to the bottom of your radiator. The drain plug is approximately 2-3 inches from the coolant line that is closest to the drivers side of the car. Real hard to see. It may be partially covered by the rubber padding that the radiator sits on, but it is right there by the transmission coolant line that is closest to the drivers side.

Aug 12, 2012 | 1997 Isuzu Rodeo

1 Answer

Remove cv axel on 01 isuzu trooper


You must remove the axle from the transmission in a straight out line from the case of the transmission in a quick and very hard snapping motion, a large heavy cast iron pipe wrench works well, but remember the axle can't be at an angle, it must be straight out within a few degrees.

Apr 27, 2012 | 2001 Isuzu Trooper

1 Answer

1997 isuzu rodeo front CV shafts ,how to separate from pumpkin


The axel should just snap in a good sharp pull should remove it.

Nov 30, 2010 | 1997 Isuzu Rodeo

1 Answer

1997 Isuzu Rodeo- What tool/pump is needed to add trans fluid


what size engine?

Usually you just fill with a funnel, unless it is at an awkward position.

Jul 12, 2010 | 1997 Isuzu Rodeo

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...