Question about Honda Cars & Trucks

1 Answer

The crv4 honda d4 light is just blinking which is making the car difficult to pull.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 31 Answers

Change your fluid transmission.

Posted on Aug 19, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: 1994 honda accord

The D4 light blinking indicates there is a diagnostic trouble code stored.When a malfunction occurs,the vehicle computer records the code and stores it,then flashes the D4 light to let you KNOW there is a problem.On pre OBD 2 Honda vehicles,1995 and back,Hondas are manual code read,which means you do NOT hook up a scan tool as there is no scan port.The passenger side front kick panel is removed,and a blue 2 wire connector located.Use a jumper wire to short out the connector,then turn the ignition key on,with engine off,not running.This throws the computer into self diagnostic mode,and the D4 or "s" light will flash a series of flashes.The flashes have to be counted,and written down.For example,2 flashes followed by 4 flashes would be a code 24.The code is then looked up with reference material for a description and diagnostic route.Every diagnostic trouble code,has a diagnostic route,for repairing the problem.Again,this informtion,the diagnostic route,is available in reference material from pay sources like All Data Online.After the repair is made,the battery is disconnected to clear the code.Good luck.

Posted on Aug 23, 2008

  • 1 Answer

SOURCE: The D4 light started blinking when I was driving the car.

why does the d4 light start to blink and it doesnt stop even if you put it in park?

Posted on Jan 01, 2009

jagjeffery
  • 318 Answers

SOURCE: 92 honda accord lx D4 flashes

you have a transmission fault the D4 light blinks to tell you that there is a transmission problem when the light is blinking the transmission computer put the transmission into limp home mode so it will not shift normally and you should try not to drive it very far when it gets to this stage you need to have the transmission codes check to pin point the problem

Posted on May 29, 2009

  • 1779 Answers

SOURCE: D4 blinking, spedometer not working, check engine light on

Hi, a few questions 1st. Did your mechanic check for engine codes? Is your Honda a v-6 or 4 cylinder?
The flashing D4 light indicates a possible transmission malfunction. You should avoid rapid acceleration until the cause of the light blinking is determined.
If you have the V-6, there is a diagnostic port to connect a scan tool to read any stored engine codes that have turned on the check engine light. This port is located behind the ashtray in the center console (most cars did not have this til 96).
If you have the 4 cyl engine, there is a service connector located under the dash on the pass. side. Inside the connector is what looks like a 2 wire plug should be attached. Take a paper clip, unbend it, and insert the 2 ends of the clip into the connector to 'jump' it. Turn the ignition switch to the on position (don't start the vehicle), and the check engine light will flash. Count the flashes, short flashes are for code #'s 1 to 9 (single digit code), a 2 digit code will be a long flash for the 1st digit, followed by a short flash for the 2nd digit. If there is more than one code, they will be separated by a pause. They will repeat so you can count them and write them down. Let me know what the code #'s are so I can help further. Curt

Posted on Jul 22, 2009

  • 170 Answers

SOURCE: 1999 honda odyssey won't start, has power but won't start.

It's the neutral safety switch. Have your mechanic adjust it, or replace it if it's bad. For now try starting it in neutral instead of park or even try pushing the shifter up all the way (in park) while you turn the key.

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 Honda Prelude D4 light blinking


This is a fault code in the trans. One solution is ti disconnect tge bsttery fir 10 to 15 minutes this will reset the trans. Control unit. If thus does not work it could need a rebuild.

Mar 25, 2013 | 1992 Honda Prelude

2 Answers

Blinking d4 light with intermittent speedometer


Usually it means the speed sensor in the transmission is failing.
The blinking light means your overdrive may not work.

Dec 11, 2012 | 1995 Honda Accord

1 Answer

D4 light is blinking on my honda accord 1992 And will not start


My d4 light is blinking and my transmition is shifting very wierd, not enough power.

Jun 06, 2011 | 1992 Honda Accord

1 Answer

D4 light on no matter what gear i'm in. 95 Honda Accord LX 4-cylinder. Already replaced solinoid, speedometer, fan,


The D4 light is coming on to tell you that there is one or more fault codes set in your transmission control module. The only way to retrieve codes on the 1995 models is to read "Flash Codes" output by the D4 light. (See instructions below)

RETRIEVING FLASH CODES USING THE D4 LIGHT
If fault codes are present, the D4 light will "blink" when the ignition is turned to the RUN position and will remain on at all times when the engine is running.
To retrieve the flash codes, turn the ignition switch off.
Install a jumper wire between the service check connector terminals.
The service check connector is a gray, 2-pin connector located on the PCM/TCM cover under the passenger side of the instrument panel. (See picture below)

CAUTION: DO NOT use the 3-pin located next to the service check connector.

Installing the jumper will place the PCM/TCM in diagnostic test mode.
Turn the ignition to the RUN position. Codes will be output by blinking the D4 light.
Note the number of blinks from the D4 light. A short blink indicates a single digit flash code. A long blink equals 10 short blinks. For instance one short blink indicates code 1. One long blink and four short blinks indicates code 14. If there is more than one fault code, they will be output one at a time from the lowest numbered code to the highest numbered code. It is recommended that you read the code or codes several times to make sure that you are reading it correctly.

Once you have retrieved the fault code(s) re-post your question and include the information for what codes you have and someone can then help you locate the cause of the problem.

May 22, 2011 | Honda Accord Cars & Trucks

2 Answers

The D4 light keeps blinking and when this happens the trainny doesnt shift right. I have diconnected the battery, this did work, but did it again after about 3 times driving it.


When the shift lever is in Park, is the D4 light on, or blinking? If the D4 light is on steady, while the shift lever is in Park, chances are your transmission computer has taken a dump on you. If the D4 light is blinking while the shift lever is in Park, the computer has stored a code, that will give you some idea where to look for the problem. Here is a link describing how to retrieve the codes. Good luck.
http://home.earthlink.net/~michaelpkeefe/HowTo_Codes.htm

Jan 21, 2011 | 1993 Honda Accord

1 Answer

I have a 2004 honda accord and it drives funny my d4 light in my dash board is blinking when i drive


A blinking D4 light on a honda is an indicator that the computer has determined there is a fault within the transmission. You would need a scanner to communicate with the pcm and read the fault codes.

Aug 24, 2010 | Honda Accord Cars & Trucks

2 Answers

92 honda accord lx D4 flashes


you have a transmission fault the D4 light blinks to tell you that there is a transmission problem when the light is blinking the transmission computer put the transmission into limp home mode so it will not shift normally and you should try not to drive it very far when it gets to this stage you need to have the transmission codes check to pin point the problem

May 29, 2009 | 1992 Honda Accord

2 Answers

D4 gear lights ( dashboard ) starts blinking even I'm using other gears


The D4 light blinking is the vehicle computer telling you there is a transmission malfunction and transmission codes are stored in the computer's memory.The codes have to be pulled out manually unless it has an OBD2 connector.A transmission shop or Honda dealer can pull the codes.

Jun 22, 2008 | 1995 Honda Odyssey

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...