Where is wiring loom for front driving lights understand loom is fitted

I would get a replacement loom from a scrap yard/breakers yard and fit that.

wiring harness is used to connect all the electronic devices in the vehicle from front bumper through to the back bumper
three sections
front engine bay loom
interior looms
rear vehicle loom
wiring loom covers
lighting
motors
communication and monitors
starting and charging
switches and levers
door locks
engine management and transmission computers

Check with a tow bar fitting shop as there will be a loom that is available for this. You will remove the socket to a light assembly and fit the new loom to the light assembly . then plug the car loom into the new wiring loom and it is all set to go . IF doubtful pay a small bit and have the shop do it for you

If the wire harness (loom) were the correct one (from Ford?), it should have fit perfectly. If it's not a Ford or Motorcraft part, you probably should return it and get the correct part.

the wiring loom that is near the collision damage area needs to be checked. I would suggest getting insulation tape black. Then carefully cut the old insulation tape on the loom and see if there is damage to any of the wires and a possible bare wire touching another bare wire. Putting insulation tape on the bare wires if found and then retape up the wiring loom should fix the issue unless the wires are broken then you need to solder the wire togwether and then insulation tape The color of the wire at the headlight would be the wires you should look for in the loom.

using the original wiring and a new live wire. this can be used on the tow wiring loom located under the boot cover at the bottom. and a relay. wire the the new light up and place the earth wire on a good earthing point.use a wire from the reversing wire and connect to the relay switching side of the relay and use the live wire from loom for tow wire. also place a fuse on this wire 10amp will be fine. if you are using the 2nd reversing lights for a caravan etc don't use this live wire use a new wire. most wiring looms have a wire on to loom for reversing light. so check that first. it can handle 2 new lights at a maximum of 10w which is adequate for the new lights. as you have not said what year astra it is both of these should work fine. there is also a main live in the pass side rear side compartment used for electrical extras cd player etc there will be a plug with nothing connected to it. it is ignition control 25amp rating. so a 10amp fuse will be fine on this line.

Hi there. You are not going to believe this, but the sister brand SEAT had this most interesting problem. Because of a fuel tank breather problem, fuel/gas was being forced up and out the fuel tank and along the length of the wiring loom and it caused all sorts of electrical problems. A new front to rear wiring loom had to be fitted after having sorted the fuel tank breather problem. Firstly, check that the fuel tank breather system is working properly - make sure that the right petrol/gas tank cap is fitted for example. It's a shot in the dark, but worth mentioning. Best regards, Scottech.

The connectors for towing wire harnesses on foresters are generally on the passenger side, below the rear taillight inside the cargo space. some require pulling up the foam block that is between the spare tire compartment and the taillight. Check where you replace the tailights from inside the car, if there isn't a matching connector hanging out there, check around the spare tire compartment, see if you can remove the carpeted foam block next to the compartment and find the plug under there.

any aftermarket lights have to have the wire loom ran. when you run the loom make sure that it is protected and out of the way of things. also when going through any peace of steel make sure that you use a gromet so the wires don't get cut.

This maybe due to the fact that all manufactured wiring harnesses installed in the corolla are standard looms, you will probably find that you do not have rear speakers installed, however the wires are located beneath the speaker grill by the parcel shelf. the standard corolla stereo only uses front speakers,but the loom has the ability to connect 4 speakers.most manufacturers always fit 1 standard loom as it is cheaper to install a full loom than make variations for different specs and models.check your stereo to see if it is used with 2 or 4 speakers. regards neil