Question about Ford Cars & Trucks

1 Answer

1948 ford f1 ford pickup - Ford Cars & Trucks

Posted by on

  • David Harrelson
    David Harrelson Apr 27, 2015

    Hi michael null, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? Do you have a question?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Ford Master
  • 2,907 Answers

I really liked my 1940 Ford convert.
Hope this helps.

Posted on Apr 27, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the VIN plate located on the 1949 F1 Ford Pickup, on the inside of the glove box or someplace else.

My guess would be to try
(1) on the chasis under the hood readable when you face the opened hood (bonnet)
(2) at the bottom of the vertical door post on the driver side.

Feb 08, 2016 | Ford Cars & Trucks

1 Answer

How do i remove the speedo drive from my gearbox it's a 1948 ford f1pickup.

the speedometer drive is held in place by a single bolt on a fork. remove this fork and pull drive out of output shaft housing.

Apr 27, 2015 | Ford Cars & Trucks

1 Answer

Locate 1948 ford deluxe vin location

It wouldn't have one!

The engine and chassis would have separate serial numbers.

Feb 11, 2015 | Ford Cars & Trucks

1 Answer

How do i change a 6 volt system to a 12 volt system on a 1948 dodge pickup

Voltage conversion necessitates the replacement of all 6 volt light bulbs and motors with 12 volt light bulbs and motors (including the starter), plus the addition of a ballast resistor to the ignition primary so that the ignition primary can continue to operate on 6 volts. You will need to refit a 12 volt starter solenoid, alternator, and regulator to the vehicle as well. Needless to point out that you will also need to replace the radio. You can use the original wiring if it is in good condition, and all switches should operate adequately as long as their insulators are still intact. The 12 volt system uses less current than the 6 volt system, so there should be no problem with wire gauge.
IMPORTANT: If the original system is POSITIVE GROUND instead of NEGATIVE GROUND, you will need to verify the polarity of all motors you replace, plus reverse the polarity of the ignition coil primary.

May 12, 2014 | Cars & Trucks

1 Answer

1948 ford flathead eight cylinder with no spark to spark plugs

Sounds as if you have a magneto problem but that is a little before my time

Aug 27, 2010 | Ford Crown Victoria Cars & Trucks

1 Answer

Trying to rewire 1948 Ford 2 door

Check out faxonautoliterature. They list the original Ford service manual for $79 or a reprint for $20. It should have the wiring diagram in it. They would be able to tell you before you bought. I've used them before and had excellent service. Hope this helps.

Mar 01, 2010 | Ford Fusion Cars & Trucks

1 Answer

Looking for firing order for 1948 ford flat head

According to my book the firing order for a 1948 V8 is 1-5-4-8-6-3-7-2. The right bank is 1-2-3-4 and the left bank is 5-6-7-8. Hope this helps.

Feb 17, 2010 | Ford F Cars & Trucks

1 Answer

Wondering what kind of grease should be in the steering box of a 1952 ford F1 pickup name is Keith..and i have restored a 1949 and a 1953 Ford F-1 pickup..and they used 90w rear end oil..i hope this helped

Jul 04, 2009 | Ford F Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5675 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides