Question about 2007 Daihatsu Sirion 1.3

Open Question

Clutch kit replacement - 2007 Daihatsu Sirion 1.3

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace clutch master kit?


pipe spanner undo steel pipe line

under the dash
undo pin release .... top of clutch pedal
undo nuts holing clutch master to fire wall
fit new unit

26338805-vgifjk0cmh4fityltrfmb02q-5-0.png

26338805-vgifjk0cmh4fityltrfmb02q-5-1.jpg

Nov 03, 2016 | Cars & Trucks

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

1 Answer

Clutch pedal soft barely disengages


1. there is clutch master cylinder kits that gets worn over time and turns the fluid greyish, they need to be replaced, But the master cylinder has to be smooth inside with no ridges or scratch that may damage the replaced kits. New fuild is needed after replacing the kits.
2. breeding the clutch system is necessary after assembling

Feb 21, 2013 | 1999 Chevrolet S-10 Pickup

1 Answer

Have replaced the clutch kit and the jeep still wont go into gear why


DOES IT GO INTO GEARS WHEN STOPPED AND ENGINE OFF?IF YES THEN IT SOUNDS LIKE POSSIBLY BLEEDING THE SYSTEM IF HYDROLICK SYSTEM ORLINKAGES MIS ALIGNED OR BENT.GOOD LUCK.ALI

Jun 14, 2012 | 1992 Jeep Cherokee Sport

1 Answer

How Do You Replace Clutch Master cylinder


honda civic.... replaced with new clutch and clutch kit... now i have to replace the clutch master cylinder..... only done 167k since new clutch.... should this have been checked when the clutch was replaced?

Jan 11, 2011 | 1998 Chevrolet Camaro

1 Answer

I have a 2003 mark 4 1.8 gti golf and the mechanic has said that I need a new clutch kit. I can change gears fine, no smell or noises, also the gear engages when I release the clutch about a quarter of the...


I am not familiar with Volkswagon products, per se, but the basics are the same. Is your clutch hydraulic? They tend to go without notice. If it is not - there may be adjustment in your system. If there is no smell and you are still able to drive ok - I am not sure what the problem is. If in fact you do need a new "kit" - do not replace just part of the kit since the labour cost of putting in a part latter would outway any advantage at this point. I did this as a teen in one of my vehicles by not replacing the throw out bearing and it failed long before the new clutch was even close to being worn out.

Nov 26, 2010 | 2003 Volkswagen GTI

1 Answer

The whole process with a Clutch Kit.


Not sure what the question is, but I will attempt it by letting you know what a clutch kit is....it is the all of the parts to replacing a cltch in the car.......the clutch is not just the thing you smell when riding the clutch, it comprises of 3 main components.

1. Release bearing....

2. Pressure plate...

3. Clutch (frictioin) plate...

I hope this helps

Oct 15, 2010 | Mazda B2200 Cars & Trucks

1 Answer

Hi i have a peugeot 406 2.0 hdi 1999, when i get in the car the clutch pedal is on the floor and i have to pump the pedal for a couple of minutes, then it is ok to drive. any ideas what is wrong with it?


The clutch acting system is hydraulical, (clutch hydraulic system).
Your clutch pedal master cylinder is weak, and needs to be replaced or repaired by gasket kit replacement. Also the clutch slave cylinder can be used, and needs to be repaired (by gasket kit replacement), or replaced. The clutch system must be bled after carrying out work on the hydraulic clutch mechanism.

Dec 09, 2009 | 2006 Peugeot 504

3 Answers

Clutch is noisy,when i depress the clutch the noise goes away


this noise is caused by a noisy clutch throw-out/release bearing, that is the part that presses against the pressure plate and disengages the clutch disk, the transmission must be removed to replace this part, so it is best to replace the clutch assembly at the same time, the labor for both is the same, about 5 hours

Oct 23, 2009 | 2003 Toyota MR2 Spyder

2 Answers

How to choose the best clutch kit


you need to match your new clutch to the old one the only concern you should have is the torque value it should always be the same or exceed the the factory specs but if you exceed the torque it can be no more than 15% greater than factory specs.also remember to change the input shaft bearing/bushing in the crank

Apr 26, 2009 | 1992 Toyota Camry V6

Not finding what you are looking for?
2007 Daihatsu Sirion 1.3 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...