Question about Hyundai Cars & Trucks

1 Answer

How do you replace the timing belt of Hyundai atos?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,156 Answers

These cars are so simple to do but access is awkward to say the least ,Remove the starter motor and buy the correct tool to lock the crankshaft so you can undo the front pulley ,later models are a taper fit and winding the engine over with the starter motor to undo the front pulley will result in bent valves

Posted on Apr 26, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 40 Answers

SOURCE: Hyundai atos 1.1 2004, 100,000 what parts must be replaced

if it has one, the timing belt should be done, along with a tune up. spark plugs air filter, fuel filter. etc

Posted on Jan 02, 2010

  • 5 Answers

SOURCE: hyundai atos crank sensor keeps failing

I know this post is very old, but nonetheless I hope this helps anyone else researching this problem.
The cam belt gear located on the crankshaft wears done on the inside of the gear. This causes the gear to "wobble" and hence touch the timing sensor, which damages it and results in its failure.
This wearing of the gear is by design and Hyundai should be taken to task for this. The crankshaft does not have a key between it and the gear. The crankshaft has "flattened" sides which match the gear and prevents it from "slipping" on the shaft, but with time the flattened edges of both the crank and the gear wear out and the gear wobbles slightly. This then accelerates the damage and can cause the gear to begin to cut into the aluminium engine cover and the main oil seal.
The only resolution is a new crankshaft and gear or sell the car.
I have had my battles with Hyundai and did not win, even though i could show a design fault.
I hope someone out there can take these guys to task and actually win and so create a precedence for the rest of us.

Good Luck

3_2_2013_10_57_32_pm.jpg


3_2_2013_11_00_19_pm.jpg

Posted on Mar 02, 2013

  • 36 Answers

SOURCE: atos 1.1 torque settings

You can call a parts store, have them look up the part first for pricing, and ask if there are required torque setting for the area. Sometimes the owners manual will have some specs

Posted on Jul 10, 2013

  • 3679 Answers

SOURCE: hyundai atos 2005 driving so slowly

have you had the OBD codes read at a garage this may help to point you in the right direction,sounds like a sensor(s)

Posted on Apr 04, 2014

Testimonial: "thanx so much. I will take my car for obd tests. will give u a feedback."

  • 487 Answers

SOURCE: HOW DO I REPLACE THE THERMOSTAT IN MY 1998 HYUNDAI atos

There is a U-Tube video that shows how to do this: https://www.youtube.com/watch?v=RIC6Z4D6Q3E

Posted on Jan 10, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Iam looking for a workshop manual for a 1998 HYUNDAI atos


You can get a free copy of the manual in pdf format at: http://www.filepeep.com/download/1998-hyundai-atos/#_

Jan 10, 2015 | 1998 Hyundai Atos

2 Answers

Where is the Computer box in the Atos Hyundai?, we want to fix it


does the Hyundai atos Prime 1.1 2008 model have a computer box

Sep 12, 2014 | 2007 Hyundai Atos Prime

2 Answers

Where can i get the suspension assembly diagrams for a hyundai atos gls 2008


A haynes manual will show you everything you need to know step by step with diagrams on every aspect of your car and every repair you may need to carry out.

Jul 30, 2014 | 2008 Hyundai Atos 1.1

2 Answers

Hyundai atos has no power


Electronic diagnostic equipment will answer this quickly.
This could be related to fuel to air mixture.
The possibility is good that it is ignition and valve timing related.
It could also be a worn cam belt drive pulley (gear).
Check the condition of the cam belt drive pulley located at the bottom of the engine on the crankshaft. I have written an article previously related to this pulley wearing out and damaging the timing pick up sensor as well as throwing out igntion and valve timing. If you dont have access to electronic diagnostic equipment it might be worth your while doing this mechanical check. Remove top cam belt cover. Manually turn engine till you line up the top camshaft sprocket with the casing timing mark (tdc). Then check the position of the bottom v-belt timing mark. It should be exactly on TDC. If not, there is a cam timing issue which could be related to the cambelt drive pulley (gear).To confirm, remove the cam belt covers and check the drive pulley carefully. It will take you a couple of hours, but will help confirm this.

Jul 12, 2014 | 2006 Hyundai Atos 1.1

1 Answer

Replace cam position sensor


The Atos has a timing sensor located at the bottom of the engine by the cambelt drive sprocket (gear). The drive sprocket is bolted to the crankshaft with a timing plate. The sensor is placed next to the timing belt.There are no cam timing sensors on the cylinder head. This is a very basic engine.

Jun 10, 2014 | 2006 Hyundai Atos 1.1

1 Answer

Hyundai atos 2005 driving so slowly


have you had the OBD codes read at a garage this may help to point you in the right direction,sounds like a sensor(s)

Apr 04, 2014 | 2006 Hyundai Atos 1.1

2 Answers

Hyundai atos crank sensor keeps failing


I know this post is very old, but nonetheless I hope this helps anyone else researching this problem.
The cam belt gear located on the crankshaft wears done on the inside of the gear. This causes the gear to "wobble" and hence touch the timing sensor, which damages it and results in its failure.
This wearing of the gear is by design and Hyundai should be taken to task for this. The crankshaft does not have a key between it and the gear. The crankshaft has "flattened" sides which match the gear and prevents it from "slipping" on the shaft, but with time the flattened edges of both the crank and the gear wear out and the gear wobbles slightly. This then accelerates the damage and can cause the gear to begin to cut into the aluminium engine cover and the main oil seal.
The only resolution is a new crankshaft and gear or sell the car.
I have had my battles with Hyundai and did not win, even though i could show a design fault.
I hope someone out there can take these guys to task and actually win and so create a precedence for the rest of us.

Good Luck

3_2_2013_10_57_32_pm.jpg


3_2_2013_11_00_19_pm.jpg

Mar 08, 2012 | 2006 Hyundai Atos 1.1

1 Answer

Hyundai atos 1.1 2004, 100,000 what parts must be replaced


if it has one, the timing belt should be done, along with a tune up. spark plugs air filter, fuel filter. etc

Jan 02, 2010 | Hyundai Motor 2004 Accent

2 Answers

Fuel problem


you might want to check your cabin air filter or the charcoal canister underneath the hood. it's purpose is to remove any excess fumes from the gastank. if it's broken or clogged that would explain why you smell gas in the car

Jan 06, 2009 | 1999 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...