Question about 1996 Chevrolet Suburban

1 Answer

1996 chevy suburban hazard lights flash won't go off and only bright lights come on. Have no blinkers at all? Replaced bulbs already.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,326 Answers

Switch not working correctly. Hazard switch stuck

Posted on Apr 26, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

  • 3 Answers

SOURCE: 1998 Ford Explorer blinker problems

Have you checked the contacts to make sure they have good contact with the bulb base? I have a 1995 Ford Contour. The turn signal went out. I replaced the bulb and it would work when it wanted to. I checked the contacts and sure enough they weren't making good contact with the bulb. I took a screwdiver and slightly bent the contacts a little. It has worked good ever since.

Posted on Apr 08, 2009

redbeard00
  • 957 Answers

SOURCE: 98 Suburban Brake and hazard lights don't work

Check for power and ground at the two panel lights. GM uses a cheep circuit board design, they overheat and corrode on the other side of the board. not serviceable.

Posted on May 03, 2009

VREGG
  • 41 Answers

SOURCE: Blinkers stay solid and dont flash, Hazards work fine.

CHECK GROUND ON TAIL LIGHT HOUSING.

Posted on May 08, 2009

  • 18 Answers

SOURCE: HAVE RPLACED BULBS AND BRAKE SWITCH AND HAZARDS WORK FINE AND BLINKERS WORK TOO STILL NO BRAKE LIGHTS

check the bulbs again make sure the brake and signal light bulb has two filaments in it, the parking lights ony has one filament

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

83 Chevy S10 - the right blinker just stays lit, won't blink and no lights come on the right side at all.


put the hazard lights on and see if they all blink, if not, check the bulbs that dont blink. if all blink, (front and rear), the turn signal switch could be bad. putting the hazard lights on, checks the bulbs and wiring.

Sep 16, 2011 | 1983 Chevrolet S-10

2 Answers

I have a 2003 Chevy Malibu and when the Hazard lights are engaged they flash erratically. Anyone have an idea?


Problem is probably with the flasher it's self. Does the flasher click even after the turn signals cancel? if so, the hazard switch is the flasher on these cars. Replace the hazard switch

Oct 16, 2010 | 2003 Chevrolet Malibu

3 Answers

Have a Chevy Corsica 1996. Blinkers not working right. When I step on brake the arrow on instrument panel for the right blinker lights up. When use left blinker, both flash like the flashers are on. ...


It sounds like a bad light socket. The brake light and the parking/running/regular part of the socket are shorting out. When you press on the brake petal it's shorting out on the turn signal and sending current to the indicator (arrow) on the dash.. When you use the blinker, it's shorting with the brake light and causing them both to flash...

Check the socket and get back to me with the result.

Mar 14, 2010 | Chevrolet Corsica Cars & Trucks

1 Answer

Where is the exact location of the hazard light flasher for a 1989 GMC Sierra C2500, and what is the possibility that it is the true problem behind the hazards not working? Beyond my hazards not working my...


Are you sure the right side bulbs all flash? You say you replaced all the bulbs? Why would you replace bulbs that were working? Did you have this problem before you replaced the bulbs, or after. The hazard flasher is down under the dash, left side, turn the signals on and follow the clicking noise.The hazard flasher and the turn signal flasher should be near each other, and are interchangeable. If it clicks fast, a bulb or a bad socket is usually the cause. These trucks have a lot of problems with the tail light circuit boards.

Nov 04, 2009 | 1989 GMC C2500

1 Answer

Rapid blinkers and hazard switch


first check all of the bulbs are good. on some cars if a bulb is burned out the blinker will flash faster than normal.

Nov 02, 2009 | Audi A6 Cars & Trucks

1 Answer

Blinkers on 1999 chevy 2500


have you walked around and check the turn signal bulbs and sockets for burned bulbs and/or corrosion? if so then you might want to look at getting a new turn signal handle " stalk" . good luck and let me know what you find out.

Mar 06, 2009 | 2005 Audi A6

Not finding what you are looking for?
1996 Chevrolet Suburban Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...