Question about 2000 Lincoln Navigator

1 Answer

Where is the CHT sensor on 2000 lincoln navigator

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Lincoln Master
  • 880 Answers

In the cylinder head. it is a temp sensor that is not part of coolant temperature circuit but rather the cylinder head temperature

Posted on May 11, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 883 Answers

SOURCE: 2000 lincoln navigator 90k mile service

Normal Maintenance Details
90,000 Miles (144,000 Kilometers) : All Applicable Models
PERFORMED OPERATION COMPONENT
INSPECT BALL JOINTS
If equipped.
INSPECT BRAKE SYSTEM
Inspect brake pads, shoes, rotors, drums, brake lines & hoses.
INSPECT COOLING SYSTEM HOSES & CLAMPS
INSPECT DISC BRAKE PADS & ROTORS
INSPECT DRIVESHAFT
If equipped.
INSPECT DRIVESHAFT/PROPELLER SHAFT U JOINTS
INSPECT EXHAUST SYSTEM AND HEAT SHIELDS
INSPECT PARKING BRAKE SYSTEM
INSPECT STEERING LINKAGE
INSPECT SUSPENSION COMPONENTS
LUBRICATE DRIVESHAFT/PROPELLER SHAFT U JOINTS
LUBRICATE STEERING LINKAGE
REPLACE AIR CLEANER/ELEMENT
REPLACE AUTOMATIC TRANSMISSION FLUID
REPLACE CABIN AIR FILTER
If equipped.
REPLACE CLIMATE-CONTROLLED SEAT FILTERS
If equipped.
REPLACE ENGINE OIL
REPLACE ENGINE OIL FILTER
REPLACE FUEL FILTER
ROTATE TIRES
90,000 Miles (144,000 Kilometers) : RWD
PERFORMED OPERATION COMPONENT
LUBRICATE BALL JOINTS
2000 Lincoln Navigator
Maintenance
...sorry if not too readable

Posted on Jun 13, 2008

  • 1 Answer

SOURCE: 2000 lincoln navigator shimmys and almost stalls

Check for Vacuum leaks near the intake manifold.

Posted on Jun 22, 2009

  • 1757 Answers

SOURCE: diagram 2000 lincoln navigator 5.4 firing order

My apologies for the delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.
I do not know if you still need this information, but I am answering it either way.


For the 5.4L:
Firing Order:
1-3-7-2-6-5-4-8
Cylinders:
(back of engine)
4-----------8
3-----------7
2-----------6
1-----------4
(front of engine)

Again my sincerest apologies....

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Posted on Mar 04, 2010

dttech
  • 4803 Answers

SOURCE: 2000 lincoln navigator defrost it's warm and does not defrost

There are several possible causes for this. Please red the following article:
Why Is My Heater Cold?

Posted on Dec 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse number for a 2000 lincoln navigator door lock switch


On this website (link below) you find fuse box diagram and description for Lincoln Navigator First Generation (1998 - 2002)

Lincoln Navigator fuse box Auto Genius

Nov 13, 2015 | 2000 Lincoln Navigator

1 Answer

I have a 2000 crown vic and my coolant fan wont come on unless i cut the a/c on or unplugged the cylinder head sensor i changed thermostat and temp sensor it still same thing what could be the problem


You have a wiring problem from sensor to the PCM - engine computer .
DL22 CHECK CHT SIGNAL CIRCUIT FOR SHORT TO GROUND
    Note: Refer to the PCM connector pin numbers in the beginning of this pinpoint test.
  • Disconnect PCM.
  • Measure resistance between CHT signal and SIG RTN circuits and then between CHT signal and PWR GND circuits at the PCM harness connector.
  • the PCM is what controls the cooling fan !
  • This Pinpoint Test is intended to diagnose the following:
    • Cylinder head temperature (CHT) sensor (6G004)
    • Harness circuits: CHT, VREF, and SIG RTN
    • Powertrain control module (PCM) (12A650)

    Tables and Graphs

    On applications that do not use a ECT sensor, the CHT sensor is used to determine the engine coolant temperature in place of the ECT sensor. In this case the PCM may store both CHT and ECT Diagnostic Trouble Codes (DTCs). To cover the entire temperature range of both the CHT and ECT sensors, the PCM has a dual switching resistor circuit on the CHT input. A graph showing the temperature switching from the COLD END line to the HOT END line with increasing temperature and back with decreasing temperature is included. Note the temperature to voltage overlap zone. Within this zone it is possible to have either a COLD END or HOT END voltage at the same temperature. For example, at 90°C (194 °F) the voltage could read either 0.60 volt or 3.71 volts. Refer to the table for the temperature to voltage expected values.
    Voltage values were calculated for VREF = 5.0 volts. These values can vary 15 percent due to sensor and VREF variations.
  • DL1 DTC P1288 OR P1116: CHECK OPERATION OF CYLINDER HEAD TEMPERATURE SENSOR
    • Run engine at 2000 rpm until engine temperature becomes stabilized.
    • No Starts or Vehicle that Stalls:
      • GO to DL3 .
    • Check that upper radiator hose is hot and pressurized.
    • Rerun Key On Engine Running (KOER) Self-Test.
    Is DTC P1288 or P1116 present? Yes No GO to DL2 . Engine temperature was not stabilized. REPAIR any other DTCs as necessary. DL2 CHECK VREF CIRCUIT VOLTAGE AT TP SENSOR
    • Refer to schematic at the beginning of this pinpoint test.
    • Disconnect throttle position (TP) sensor.
    • Key on, engine off.
    • Measure the voltage between VREF and SIG RTN circuits at the TP sensor harness connector.
    Is voltage between 4.0 volts and 6.0 volts? Yes No There is sufficient VREF voltage. RECONNECT TP sensor. GO to DL3 . GO to C1 . DL3 CHECK RESISTANCE OF CYLINDER HEAD TEMPERATURE SENSOR WITH ENGINE OFF
    • Disconnect CHT sensor.
    • Measure resistance between CHT signal and SIG RTN pins at the CHT sensor. Refer to the table at the beginning of this pinpoint test for resistance specifications.
    Is resistance within specification? Yes No For No Starts or Stalls, RETURN to Section 3 , Symptom Charts.

    All others, GO to DL4 . REPLACE CHT sensor. You need a scan tool to do some of these tests
  • DL4 CHECK RESISTANCE OF CHT SENSOR WITH ENGINE RUNNING
      Note: Verify that engine is at operating temperature before taking CHT readings.
    • Run engine for two minutes at 2000 rpm.
    • Measure resistance between CHT signal and SIG RTN pins at the CHT sensor. Refer to the table at the beginning of this Pinpoint Test for resistance specifications.
    • Key off.
    Is resistance within specification? Yes No REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ). REPLACE CHT sensor. DL5 DTC P1289 OR P1290: ACCESS CHT PID AND CHECK VOLTAGE
    • Connect scan tool.
    • Key on, engine off.
    • Access CHT V PID.
    Is the CHT V PID less than 0.2 volt? Yes No GO to DL6 . GO to DL7 . DL11 CHECK CHT SENSOR SIGNAL AND SIG RTN CIRCUITS FOR OPEN IN HARNESS
      Note: Refer to the PCM connector pin numbers in the beginning of this pinpoint test.
    • Disconnect PCM.
    • Measure resistance of CHT circuit between PCM harness connector pin and CHT sensor harness connector.
    • Measure resistance of SIG RTN circuit between PCM harness connector pin and CHT sensor harness connector.
    Is each resistance less than 5.0 ohms? Yes No REPLACE PCM (refer to Section 2, Flash Electrically Erasable Programmable Read Only Memory (EEPROM) ). REPAIR open circuits. free wiring diagrams at www.bbbind.com

Jul 13, 2015 | Cars & Trucks

2 Answers

Where is the rear axle sensor on a 2000 lincoln navigator?


One of 2 places. First in the rear axle housing just above where drive shaft bolts. Or you have 1 wheel sensor on each wheel. Depending on the options is depending on what location you will find it.

Jun 29, 2014 | 2003 Lincoln Navigator

2 Answers

Can not find the location of the coolant temp sensor on my 2005 Lincoln ls


CHT-Cylinder Heat Temperature Sensor

V6--Driver Side--between COP Coil 5 & 6

V8-work in progress & I own one

NO CTS Sensor,odd I know

Mar 05, 2011 | 2002 Lincoln LS

1 Answer

2000 lincoln navigator turns over fine will not start just replaced fuel pump


Has anyone checked, your crankshaft sensor. Check for spark,fuel pressure.

Oct 28, 2010 | 2003 Lincoln Navigator

1 Answer

2000 lincoln navigator fuse box diagram


You find here (link below) fuse box diagram and description for Lincoln Navigator First Generation (1998 - 2002)

Lincoln Navigator fuse box Auto Genius

Jan 12, 2010 | 2000 Lincoln Navigator

1 Answer

I have the air bag light ''on'' on my lincoln navigator 2000.


Remove clips from battery and then check carefully all the air bag sensors i.e under driver seat or passenger seat. Best way is a computer diagnose to find the right cause from car's ecu.

Sep 07, 2009 | 2000 Lincoln Navigator

4 Answers

Location: Coolant Temp Sensor 2001 Lincoln LS V6


It is on the Driver side of engine in between the COP's (Coil on plugs) simply unplug the wire use a 19 or 3/4 deep well socket and unscrew it and put it new one... The whole process should only take 10-15 minutes.

Jan 11, 2009 | 2000 Lincoln LS

1 Answer

2000 lincoln Navigator air suspension


There are level control sensors they look like little arms (with joints like your elbows) mountesd on lower control arms. They may be at fault they control the height and turn the pump off when the height is reached. try adjust height first before you replace, they can be adjusted. Good Luck

Dec 17, 2008 | 2000 Lincoln Navigator

Not finding what you are looking for?
2000 Lincoln Navigator Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...