Question about 1998 Ford Crown Victoria

1 Answer

Have a 98 crown vic i can press the gas pedal to the floor and the speed wont get pass 10 r 15 mph ive changed motors twice Same problem ...help plz b4 i trash the car

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 333 Answers

Hello, I suspect you have a restriction in your exhaust system.

Posted on Apr 26, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: 98 galant motor stalls - dies when gas is pressed

I would take a look at possiable damage to the PCM (powertrain control module)

Posted on Nov 19, 2008

polarcycle
  • 1392 Answers

SOURCE: Lack of power

Start with IAC motor, TPS sensor, possible clogged catalytic converter.

Posted on May 30, 2009

  • 439 Answers

SOURCE: 1988 Ford Crown Vic Strange Idle

When you turn the key on does the check engine light come on? If not it may be burned out. It sounds like a MAP sensor or an O2 sensor is bad. I would suggest taking it to autozone as they do free diagnostic and seeing if a code comes up. If it is a sensor it should, if not it may be the idle sensor not reading right in the ECU. More than likely it is one of the sensors though.

Posted on Jun 23, 2009

  • 66 Answers

SOURCE: 99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Posted on Jul 07, 2009

  • 5 Answers

SOURCE: I have a 98 Crown Vic, It feels like it has a

Maybe, Ford motors are sensitive to airflow changes, a slow responding MAF can cause delayed signals to real world conditions. An UNDERreporting MAF will ENLEAN the fuel charge as delivered to the injectors. This can feel like or perceived to be a misfire/coil problem, BUT ONLY UNDER A LOAD. Check all PCM inputs, condition of components.What is more logical: EIGHT (8) coils OR EIGHT (8) injectors failing AT THE SAME TIME? I would look at a single component scenario insteadwise, fuel pump? ACT sensor? TPS? EGR solenoids? MAF?

Posted on Feb 14, 2010

Testimonial: "This is a great website and just like to say thanks for your input."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Ford Crown Victoria (police pkg) wont start?


The first thing you need to do is have the computer scanned for trouble codes to narrow down the possible causes. But that would require a code reader or scanner.
Have you checked fuel pressure with a gauge ? Are you getting spark to the plugs ? Because of the moan from the pump, there's a good chance the pump has failed.

Apr 22, 2013 | 2000 Ford Crown Victoria

1 Answer

1999 crown vic wont start


Are you saying it won't crank, or won't start ?
If it does not crank, and you have replaced the battery and starter, the problem may be in the neutral safety switch.

Dec 08, 2012 | 1999 Ford Crown Victoria

1 Answer

1988 forn crown vic misfire?


If the cap rotor and plug wires are original, I would look at them first.
Also check the condition of the plugs.

Jul 12, 2012 | 1988 Ford Crown Victoria

1 Answer

92 dakota bad vibration 30-55 mph


bent tyre or dish rim, check tyres and rims and speed balance would help.

Feb 11, 2012 | Cars & Trucks

1 Answer

2000 crown vic p71 random misfire changed all plugs some coil packs now when i floor it i will instantly or some time short after start missfiring on all 8 sounds like **** rough loss of speed gas pedal...


If you already changed plugs, rotor and cap please consider fuel filters ( both in-line and in the carbeurator). If that doesn't resolve the problem look at timing, timing chain and/or missing teeth on the flywheel which would cause slipping and misfiring.

Sep 19, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

01 Crown vic will not stay crunk


get the auto choke operation checked,or a good tuneup

Jul 08, 2010 | 2001 Ford Crown Victoria

2 Answers

I have an 02 crown vic and now the blower motor just quit working i put a new motor on it and checked the fuse but it still dont work ive been reading up and there seems to be alot of peolpe saying the...


On my 2004 Ford Crown Vic One day it just stoped blowing no A/C or heat i checked all the fuses and relays and they are fine so i guess its the blower motor and i want to know the location and if is easy to chang \??? Or if might be somthing else ccan you help???

May 22, 2010 | 2004 Ford Crown Victoria

1 Answer

98 galant motor stalls - dies when gas is pressed


I would take a look at possiable damage to the PCM (powertrain control module)

Nov 19, 2008 | 1998 Mitsubishi Galant

Not finding what you are looking for?
1998 Ford Crown Victoria Logo

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...