Question about Cars & Trucks

1 Answer

Where is the relay at on a 2000 VW bug for secondary air injector

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,173 Answers

Posted on Apr 25, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 vw cabrio runs normal and shuts down, takes 5

Did you ever get to the bottom of this problem? My car has the same codes- dealer says it might be the fuel pump relay. Wondering what you found out?

Posted on Jul 28, 2010

  • 1 Answer

SOURCE: secondary air injector system...circuit relay

There is a relay under the car under the driver seat. The air pump is right next to it. You should hear the air pump come on when you start the vehicle. If not the relay is bad. You can jump the relay to see if the pump is bad or the relay is bad.

Posted on Aug 29, 2009

  • 7 Answers

SOURCE: 2000 Bug

Is it not blowing enough air or is the air never getting cold the first may be a clogged cabin air filter a pain to get to need to remove the center and right side of the dash top plus anothe cover to get to it.

Posted on Aug 17, 2008

  • 883 Answers

SOURCE: vw passat 2000 1.8t front wheel drive

please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Posted on Jun 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Error code p1472 p1225 p1227 p1228 p1226 p1425 p1435 p1421 on 2000 volkswagon bug


P1472 Electrodrive Fan 2 Operational Failure (Passenger Side)
P1225 Needle Lift Sensor Malfunction
P1227 Waste gate Failed Closed (Over Pressure)
P1226 Control Sleeve Sensor Malfunction
P1228 Waste gate Failed Open (Under Pressure)
P1421 Catalyst Damage
P1425 EGI Glow Plug Secondary Failure
P1435 A/C Refrigerant Temperature Circuit Range/Performance
You need an expert to loo into this, the dealer is the best option out there, more cost but they will fix it faster.

Nov 17, 2016 | Cars & Trucks

1 Answer

Where can I find the fuse and relay for air injector pump on a 2005 chevy trailblazer LS?


AIR SOL - fuse #54 15amp - AIR fuse #56 60amp location under hood fuse / relay box
54
AIR SOL Fuse
15A
AIR SOL Relay, Secondary Air Injection (AIR) Pump Relay, Secondary Air Injection (AIR) Pump, Secondary Air Injection (AIR) Solenoid
55
AIR SOL Relay
--
Secondary Air Injection (AIR) Solenoid

Sep 13, 2016 | 2005 Chevrolet TrailBlazer LS

1 Answer

What does code number 1451 mean on a 2000 VW bug


Secondary air injection circuit short to ground don't know what it means. Looked it up in data base

Apr 27, 2015 | Cars & Trucks

1 Answer

Code p0418


code p0418efers to secondary air injection (AIR) pump relay A--circuit malfunction ====causes --wiring---air pump relay---ECM
replace the relay and check out the wiring and connections.

Dec 17, 2013 | Volkswagen Cars & Trucks

1 Answer

I have a 2000 vw passat GLX V6 5 Speed with the error codes p1411 -p1423 how do i fix it


P1411 = Secondary air injection system, bank 2 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.

P1423 = Secondary air injection system, bank 1 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.


Mar 13, 2011 | 2000 Volkswagen Passat 4Motion

1 Answer

Code P1420 suggests replacing the secondary injection pump relay, where is the relay?


17828/P1420/005152 - Secondary Air Injection Solenoid Valve (N112): Electr. Malfunction Possible Causes
  • Secondary Air Injection Solenoid Valve (N112) faulty
  • Secondary Air Pump Relay (J299) faulty
Possible Solutions
  • Check Secondary Air Injection Solenoid Valve (N112)
  • Check Secondary Air Pump Relay (J299)
The secondary air injection pump relay (J299) is inside the engine compartment, left side, behind air cleaner housing, under a black plastic protective cover you can lift up to reveal it. It's near the brake fluid reservoir beside the odd black plastic cover for the wiring harness beside the shock absorber tower.

Rating my suggestion let's me know how helpful it was correcting your problem. Your rating is truly appreciated and would take the very least of time and effort away from you. Thank you

Jun 17, 2010 | 2000 Volkswagen Beetle

3 Answers

2000 vw cabrio runs normal and shuts down, takes 5 to 20 minutes to restart, engine cranks but doesnt start, changed ignition coil, pulled diagnostic codes getting short to ground codes on cylinder...


On some models, the Engine Control unit has a power supply relay. These relays some times get internal dry solder points. After driving for some time the the solder will get hot and separate. When it cools down it makes contact again. You will have to replace this relay or open it up and re- solder the solder joints. The relay is usually located on the main relay station in position 3. the relay station is located behind the right dash panel.[right hand drive vehicles]. You may need to refer to a manual for your specific model to find the exact location of the relay.

Jun 04, 2010 | 2000 Volkswagen Cabrio

2 Answers

Car is choking out and dying. Reads P 0411 code. How do I know if its the motor or just the solenoid valve? How can I check to narrow down what actually is causing the problem? It's on a 2000 VW jetta VR6


16795/P0411/001041


if (window.showTocToggle) { var tocShowText = "show"; var tocHideText = "hide"; showTocToggle(); } 16795/P0411/001041 - Secondary Air Injection System: Incorrect Flow Detected Possible Symptoms
  • Malfunction Indicator Light (MIL) ON
Possible Causes
  • Fuel Pump Relay (J17) faulty
  • Hoses/Pipes to/between Components faulty/clogged
  • Secondary Air Injection Pump (V101) faulty
  • Secondary Air Injection Pump Relay (J299) faulty
  • Secondary Air Injection Solenoid Valve (N112) faulty
Possible Solutions
  • Check Fuel Pump Relay (J17)
  • Check Hoses/Pipes to/between Components
    • Check Secondary Air Injection Hoses/Pipes for Carbonization
  • Check Secondary Air Injection Pump (V101)
  • Check Secondary Air Injection Pump Relay (J299)
  • Check Secondary Air Injection Solenoid Valve (N112)

Apr 28, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

2000 Bug


Is it not blowing enough air or is the air never getting cold the first may be a clogged cabin air filter a pain to get to need to remove the center and right side of the dash top plus anothe cover to get to it.

Jul 14, 2008 | 2000 Volkswagen Beetle

1 Answer

Vw passat 2000 1.8t front wheel drive


please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Jun 21, 2008 | 2000 Volkswagen Passat 4Motion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...