Question about Chrysler Cars & Trucks

1 Answer

How do you replace a broken stud on wheel for 2003 chrysler town and country

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 406 Answers

Remove the wheel..You should be able to punch the broken one out and replace it..they can be bought at any of the auto parts stores like auto zone. The new one has groves on the neck end that seats when you use the lug nut to tighten the wheel...good luck

Posted on Apr 25, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a wheel stud on the front of a 2003 chrysler town and country


In most cases the brake caliper and rotor will have to be removed. The affected stud can then be pounded out with a hammer. An air gun should be used to install the new stud using a spacer between the stud and hub assembly. Put the nut on the stud and using the air gun, pull it through un til it seats against the spacer and the hub

Apr 25, 2015 | Chrysler Cars & Trucks

1 Answer

How to replace a rear wheel stud on a chrysler t&c touring w? disc brakes


you have to drive the old one out and hammer the new one in from the back side of the hub.

Apr 21, 2013 | 2006 Chrysler Town & Country

1 Answer

I want to know how many bolts holding the starter on crysler 2003 town country and where they loccated


Looks like both engines take the same starter - should be two bolts. One could be a stud with a nut and lock washer.

Aug 31, 2012 | 2003 Chrysler Town & Country

1 Answer

I am wanting to replace the rear wheel studs that are broken. The wheel hub flange won't come off. Is there a special puller for this, do I need to apply more force or is there another method for removal?


You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Studs for rear wheel mounting broken off. How are they repleced?


First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

1 Answer

2003 Chrysler T&C EX has the Tilt Wheel stuck in the UP position.how do I fix?


The tilt is broken needs to be replaced. Part # 05083729AA Chrysler Dealer around $38. If you don't have a Chilton's Manual nows the time to buy one to remove the steering wheel & airbag system.

Feb 03, 2010 | 2003 Chrysler Town & Country

1 Answer

How to replace lug studs on 2002 chrysler town


I'll try to help you. If you are having trouble with 3 out of 5 studs on one wheel you may want to go to an autoparts store or Salvage yard to look at the whole hub. Usually a press is used to remove the bolts so you would be taking off the hub anyway. When you pay for 3 bolts and labor you may be better off in a Salvage yard or parts place for a different hub. The rear hub on front wheel drive cars is like a trailer axle. Much simpler to remove mounting bolts and press in new bolt. But if rear has differential(rear wheel drive) it has an axle shaft. Would be easier to grind and drill out broken stud on car. You can draw new bolt into place by placing bolt through a socket and use the wheel nut to draw the bolt into the hub.

Jul 08, 2009 | 2009 Chrysler Town and Country

2 Answers

How do you get the calipers off the rear?


Firstly you need to remove the park brake cables from the calipers. undo the bolts that hold the caliper to the hub assembly. lift the caliper away and yes you can buy new studs and nuts/bolts but you may need to go to a main chrysler agent to get them

May 12, 2009 | 2006 Chrysler Town & Country

1 Answer

2002 Chrysler Town and Country


Ok, i'm assuming your replacing them, there is an oval rubber stopper on the backside of the rotor, in the backing plate, located near the bottom. it will tighten or loosen the e-brake shoes inside the rotor, loosen them all the way off, then get a big hammer and give them a really good smack, be carefull not to damage the wheel studs, if your reusing them hit on the hat of the rotor, if replacing you can hit right on the rotor face.
Use some antiseize on the hub before installin your new rotors, and don't forget to readjust your
e-brake and reinstall the rubber plug

Oct 30, 2008 | 2002 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...