Question about Mazda Cars & Trucks

1 Answer

1998 Mazda b 4000 cranks sparks 60 fuel pressure but still no start

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mazda Master
  • 5,438 Answers

Check timing belt and compression.

Posted on Apr 25, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1998 mazda 2500 cranks but wontr start, has fuel to fuel rail has compression has spark to the 2 cyls that were checked

If you have at least 40# of pressure to the rail, spark, compression, and the engine is in time...that only leaves one thing. Fuel injectors. I believe that the signal to fire the injectors comes form the crank sensor to the ECU

Jan 04, 2018 | Mazda Cars & Trucks

1 Answer

My 94 mazda protege will crank but wont start. I replaced rotor and cap. Battery. Air sensor. When i try to turn over a thud comes fron the air sensor. Help please!!

If it won't start, have you checked for spark and fuel pressure? Remove one plug wire and ground it over the engine. Crank the engine and see if there is spark. IF spark is present, check fuel pressure to see if the pump is working. If spark and fuel are present, check for cracked air hose from air filter housing to throttle assembly allowing unmetered air into the engine. Also check for timing belt issues

Dec 06, 2015 | Mazda Cars & Trucks

1 Answer

1998 chevy 1500 silverado 5.7 z71 4x4 auto transmission Cranks wont start. The crsnk senser ok Has spark at coil Has good fuel pres I use start fluid thys to start What am missing Help

What engine does your truck have ? does it have The Central Sequential Fuel Injection (Central SFI) (4.3L, 5.0L, 5.7L) ? Is your fuel pressure with in (60-66 psi). if not , will not start . I find this a lot also fuel pressure regulators leaking will cause a hard start .

Nov 01, 2015 | Cars & Trucks

1 Answer

1998 c1500 cranks but no start. No codes, good fuel pressure and spark.


Sep 02, 2014 | 1998 Chevrolet C1500

1 Answer

Car cranks but will not start

This could go several ways #1 engine mechanical check cranking compression should have 125 psi or greater in all cylinders if low but even squirt oil (1/2 oz.) in 1 cylinder and retest goes higher then rings sealing has been lost. if uneven check timing belt for jumped or misalignment. #2 electrical does it have electrical spark to plugs crank engine with a spark plug connected to spark plug wire laying plug on engine can you see spark? No test ignition coil wires with a logic probe both terminals will be red with key on one will flash red/green when engine cranking does not the primary ignition needs repair Ignition module? or pick-up coil/ crank sensor. #3 fuel system pressure and injection pulse. injection pulse can be tested with logic probe DONOT USE A TEST LIGHT YOU CAN RUIN THE ECU .

Mar 21, 2014 | 1998 Mazda 626

1 Answer

99 mazda 626 cut out and won't restart has spark and fuel

When you checked fuel did you check for proper fuel pressure your pump may have pressure but not enough to keep it running. Also Check all your fuses, I had a truck crank and crank I replaced fuel filter etc and come to find out it was just a 5 amp fuse for the ignition

Dec 10, 2013 | Mazda 626 Cars & Trucks

1 Answer

My 98 mazda prodege wont start only cranks over

Well you need spark at the right time, fuel, and normal compression to make the engine run.
So you would need to check for spark and fuel, then compression if necessary.

Jan 30, 2013 | 1998 Mazda Protege

1 Answer

My mazda 626 will crank over but will not start i think someone took a fuse out

check if the car is firing by pulling an ht lead off the plugs and put another spark plug on the ht and earth the spark plug if it has spark when cranking if it is there check the fuel system if the fuel is getting to the injectors.

Jan 23, 2013 | 1998 Mazda 626

3 Answers

I have a '97 chevy tahoe. the engine cranks, but won't start. checked trouble codes & got cycliner misfire, O2 sensor, & catalytic converter codes. i've replaced plugs & wires. still won't...

first, check all the fuses
did you check to see if there's spark at spark plugs?
did you check the fuel pressure? you need to do that to isolate fuel and ignition system.
if there is no fuel then check for fuel pump operation
if there is no spark then check the ignition system (coil, module and wirings)
if you don't have either one then the problem is in the computer system such as crank sensor, and computer itself

Mar 28, 2010 | 1997 Chevrolet Tahoe

2 Answers

Where is the fuel shut off in the trunk of a 1998 Mazda 626

the shut off switch should be in the trunk left side near the outer left taillight.

Mar 13, 2009 | 1998 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides