Question about 1999 Nissan Quest

Open Question

Where is the seatbelt alarm on a99 nissan quest? it is not working.

Trying to fix it so it will work again. also the seatbelt light on dash not working?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 46 Answers

SOURCE: alarm wont shut off and I can't start vehicle

use the key and unlock the trunk...if that doesnt work do the passenger door...that should reset the alarm...

Posted on Jan 15, 2009

ewashmidas
  • 362 Answers

SOURCE: changing water pump on 1994 nissan quest

There is no easy way, water pumps are hard to change on this vehicle. Before starting the job I would buy a repair manual with step by step instructions. To give you some idea on how long it may take, the labor time is 4.5 hours for an experienced tech.

Posted on Jan 28, 2009

  • 155 Answers

SOURCE: 2004 Nissan Quest - alarm Waking the neighbors

If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they tie in and get power from a number of sources (stereo, interior lights, etc.), so you'll have to trace and unclip 8-12 wires to fully disengage. Good luck!

Posted on Jun 12, 2009

jimboz4
  • 305 Answers

SOURCE: how to take off tire pressure light off on nissan quest 2004

remove the tire pressure light fuse from fuse-box....this should work

Posted on Jul 23, 2009

johnjohn2
  • 5763 Answers

SOURCE: Reset Nissan Altima seatbelt light which is flashing

A scan tool is needed to reset the seatbelt light, unhooking the wires turned the light on as a fault, a scan tool will reset code. also make sure all connectors are connected good, the computer may reset itself after it sees a few key cycles and tests the system and it passes but it may take awhile. i have seen some that will stay on until they are reset, if the light is still on after all this time then a scan tool will be needed to turn off the light. good day.

Posted on Feb 04, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello I have a 2004 nissan quest problem dash lights do not work


are you familiar with the dimmer control?
other that that if is not the fuse I don't know what else it could
be. best luck to you.

Dec 07, 2014 | 2004 Nissan Quest

1 Answer

I have a 2006 nissan quest. The dash lights turn


No! as there isn't any "dash board computer chip". What is the code for the engine light?

Oct 04, 2014 | 2006 Nissan Quest

1 Answer

97 Nissan Pathfinder dash lights aren't working AND the alarm to turn off the headlights isn't working either.


i know this sounds crazy, but do you have break/tail lights?some cars shut off dash lites when tail/brake lights dont work

Jan 11, 2013 | 1997 Nissan Pathfinder

1 Answer

How can u stop the buzzing noise for the automatic seatbelt on 93 nissan quest? Is there a fuse?


No fuse, but on the side between the door the panel you can take off and just unhook the wire(s) and then put the panel bak on. The only problem is that the light will stay lit on your drivers dash board. But it ststop the noise with no effect, Take 20 minutes top to do this.

Jul 10, 2012 | 1993 Nissan Quest

1 Answer

1993 Nissan Quest GXE-Power seat belt retractors both create a slipping, rattling noise. The drivers side seatbelt is stuck in one position (driving position). I've tried lubricating it to no avail. Is...


I had this same problem with mine, what i did was take off that part of the interior to where you can get to the actual motor itself and disconnect the power to it.. i found out that for some reason the track to mine was completely eaten through when mine did what yours did.. just make sure its in the driving position all the way so it's safe to use while driving and it wont move. the only drawback to this is the seatbelt light stays on the dash..

Nov 09, 2010 | 1993 Nissan Quest

1 Answer

I have a 1997 toyota corolla that one of the chimes (seat belt, key ignition or lights) just started dinging and won't stop until the car is turned off.


Get in the car, make sure your dome light is set to door-operation.
Close all the doors, does the dome light go out?
If so, it's not the door ajar chime. If not, one of your door pin switches is defective.
Buckle your seatbelt, does the seatbelt warning light on the dash go out?
If so, it's not the seatbelt alarm. If not, it's the seatbelt buckle receiver.
The light warning works with the key off, so it is not that since turning the car off would not stop it.
Last thing it could be is the ignition key alarm.
I have seen a few malfunction over the years.

Sep 13, 2009 | 2001 Toyota Corolla

1 Answer

1997 Nissan Quest brake lights will not go off


there is a switch under the dash that turns on and off the break lights. it is connected to the pedle and a stationary spot under the driverside dash.try pulling up on the pedle to turn the switch off. if this does not work take it to a mechanic to replace the switch. they are not to expensive under $20.00 through napa.

Aug 24, 2009 | 1994 Nissan Quest

2 Answers

2004 Nissan Quest - alarm Waking the neighbors


If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they tie in and get power from a number of sources (stereo, interior lights, etc.), so you'll have to trace and unclip 8-12 wires to fully disengage. Good luck!

Jun 12, 2009 | 2004 Nissan Quest

1 Answer

1993 QUEST GXE SEATBELT Automatic driver side seatbelt not working.


they have a module in the center dash area adn there is a limit switch at each end of belt travel. Kind of like garage door opener.

check fuses & relays first.

go here for Quest help

http://groups.yahoo.com/group/villagerquest/

Mar 02, 2009 | 1993 Nissan Quest

Not finding what you are looking for?
1999 Nissan Quest Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...