Question about Ford Cars & Trucks

1 Answer

When checking the charging system It shows

A CODE OF LOW PO625? i JUST REPLACED BATTERRY

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Ford Expert
  • 267 Answers

The alternator is week

Posted on Apr 25, 2015

Testimonial: "Thank you Appreciate the help. Dave"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Ford Explorer, 4.0 engine, new batterry and new alternator, alternator does not recognize battery. alternator gauge shows no charge going to batrery from alternator. Any suggestions??


check and test battery and alternator new doesnt mean free from defects --check and test wiring / connections --lastly test gauge and connections

Jun 04, 2017 | Ford Cars & Trucks

1 Answer

Charge a/c 2.50 134a replaced low psi.switch still low psi switch shuts off com.low gauge showes 23 to27psi


Dis you evacuate all the air before charging the system? What is the high pressure side reading? How long does it take for the compressor to shut off? Have you checked the TPS? Maybe the computer is been told the engine is at 60% throttle which kills the compressor clutch for more power, have you replace the AC clutch relay?. I don't know lots of reasons for this.

Jul 20, 2016 | Cars & Trucks

1 Answer

Ac compressor clutch will not engage on my 98 yukon.


The most common cause of no clutch engagement is a low state of refrigerant charge in the system. Have a set of AC pressure gauges hooked up and bypass the compressor cycling switch and check the pressure on the low side charging port, you show shop 28-32 PSI at idle.

Jun 24, 2012 | Cars & Trucks

1 Answer

Rapid battery discharge


Battery discharge when connected is a regular fault when there are too many electronics connected some of them directly active even when the main switch is off. these can be the clock, the stereo system, the power amp, the remote controller, the auto lock, auto start or any other accessories. You will need to carefully go about to identify with the aid of a good ammeter. Disconnect the main battery terminal and recconnect it in series with the ammeter. If there is a leak in the system it will show up as a good reading . Usually a reading less than few milli amps can be ignored but if the current drain is high then carefully disconnect each of the acessories which is present in the car either byt disconnection of fuse or main wire to device. Once the reading drops to a very low level on discoonection of a particular device, you have the culprit in hand. Keeping this circuit disconnected and check out after two days but your batterry must be in trim condition ( not drained earlier). Hope this helps you out. Good day

Jul 19, 2010 | 2001 BMW Z3

2 Answers

Air conditioning stopped working an battery light came on


check your charging system, when batterry goes down its automatically shut off your a/c system, alternator and circuit must check

Jun 18, 2010 | 1998 Volvo S70

4 Answers

1998 jeep cherokee sport- i get a code p1682.


P1682 - Charging system voltage to low.

Nov 23, 2009 | 1998 Jeep Cherokee

2 Answers

Ac not working right


If the system was workin enough for you to add freon and stop leak you may have overcharged the system and blew out the location of the leak to make it lose enough charge that it shut down from being low on charge. There is a low pressure switch that will stop the clutch on the compressor from engaging when low on charge. The hose connections have O-rings and the system needs to be discharged and the Freon captured to replace the O-rings. ALL O-rings should be replaced at once if that is the case. Look to see where the red dye showed up if you put in the stop leak. Normally the seal in the compressor is what starts leaking first. It sounds like your leak is bad enough that stop leak will not be the answer so you may have to break down and take it to a shop to check the system.

Aug 31, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...