Question about Cars & Trucks

1 Answer

How to get the handle apart to access bit storage


Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 10,875 Answers

Turn the top

Posted on Apr 24, 2015

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need to replace emergency brake pull release handle.

then get a repair manual for your make,model,year and go to taking it apart .

Aug 15, 2016 | Cars & Trucks

1 Answer

How do I fix the door cable to the handle for a 1992 Ford truck?

Remove the door panel to access it. You will have to replace the handle and cable, they are one piece. It clips onto the door latch, you will see when you get it apart.

Jan 30, 2015 | Ford Cars & Trucks

1 Answer

How can i get bmw 323i convertible top down manualy

If your top is electric then you will need to release the front cowl motors at the center point of the trim in front of the rear view mirror(small access plug needs to be removed and allen key inserted to drive unit.) You also need to pull the release handle under the back seat bottom(driver's side) The release handle detaches the drive units for the storage lid cover and the convertible top drive. Once the motors are released, the front of the top must be lifted approximately 6 inches and the pressure against the rear of the top will relax. raise the rear bow, open the storage lid, lower the rear bow and push the front of the top up and toward the back of the car. The top should fold into the storage area. Once in, close the storage lid until it clicks.

Feb 25, 2012 | 1997 BMW 328

2 Answers

The rear access doors will not unlock on our 04 Suburban, not with a key or the buttons. All other locks work fine.

ok it sounds like the linkage has came off. You will need to crawl to the back and remove the door panel inside you will see a rod that goes from the key location to the handle this rod has bushings that can wear out change the bushings and place the linkage back in and this should fix your problem.

Dec 12, 2010 | 2004 Chevrolet Suburban

1 Answer

I couldn't open my back door of my car from the outside and then my sister decided to put child lock on and now I can't open it from inside or outside. With out being able to open the door to take it apart...

It sounds like it could be the plastic connecting bit that links the outside door lever to the rod that operates the door mechanism, has broken or become disconnected. To check, you will need to remove the trim on the inside of the door, after removing any screws and the inside door lever and window winder. However now that the child safety lock has been set it could be very difficult to get the door open.
All I can suggest is that you look at the other rear door to locate the position of the safety tab and then try to disengage it by using a suitable thin blade or something on your bad door so that you can again use the inside lever.

Once you have the inside trim off and the plastic sheet, you will see an access hole for the door mechanism and the outside operating handle of the door. It should be attached to the actuating rod by the aforementioned plastic bit. If plastic bit appears OK try re-attaching it or replacing it if broken. If the part of the outside handle which attaches to the rod is broken the handle will need replacing.

Oct 12, 2010 | 1990 Hyundai Excel

2 Answers

2004 saab 9-3 drivers window is stuck; how to take door apart

Panel is easy to remove with just 2 screws (#30 bit) in the door handle. You must first remove the cover from the handle used to close the door when getting in the car and the screws are there. The rest of the panel are snap-ins.

Sep 06, 2010 | 2004 Saab 9-3

1 Answer

2008 BMW X3, removing the left rear outer door handle.

2004 x3 Rear passenger door handle came off/apart. What are the steps to remove the inner door panel to access the door handle and repair it?

Apr 06, 2010 | 2007 BMW X3 3.0si SAV

1 Answer

The latch assembly from the tailgate handle seems to be broken or apart. How do I get into the tailgate to check it out.

you have to remove the handle. there you can gain access to the latching mechanism and rods connecting to the latch if you have a bedliner, you may have to remove the bed liner on the tailgate to get to the screws

Mar 17, 2010 | 2006 Nissan Titan

2 Answers

1997 Convertible BMW 318i top roof storage wont open

Hi, I don`t know the car but sometimes when you can`t open a boot lid someone need to push the boot lid down ( this relase the pressure of the latch system)and the same time someone pull the handle. Hope that helps.

May 28, 2009 | 1997 BMW 318

1 Answer

Driver side exterior door handle pulls the locking mech. down when the handle is lifted. can open if 1)time lifting the handle with pressing the fob button just right, or 2) someone holds down the unlock...

Take the door panel off the inside of the door. (Should involve screws at the bottom, plus bolts through the interior handle. Then pull out at the bottom, and lift upward Google for expedition door panel removal for more specifics if needed).

It sounds like the exterior handle linkage is binding against the lock button linkage. Actually looking in while pulling the handle would confirm. You then should be able to just bend the rods a bit to move them apart.

Mar 10, 2009 | 1999 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides