Question about Chevrolet S 10

2 Answers

Where is the OBD port on my 1998 chevy s10 blazer

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 121 Answers

Good anser

Posted on Apr 24, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 1,144 Answers

See pictures:


Where is the OBD port on my 1998 chevy s10 blazer - obd-port-1998-chevy-s10-blazer-f31l0ki2tmfa5vfdojcuname-5-0.jpg


Posted on Apr 24, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

jeffbvegas1
  • 520 Answers

SOURCE: Heater 1998 chevy s10

wide open hung thermostat can cause this too...continual circulation never allows the water to get hot enough to warm the heater core

Posted on Jun 23, 2009

  • 495 Answers

SOURCE: need the fuse diagran fo chevy blazer s10 4wd 1991

go to autozone.com, enter your vehicle specs, and follow the prompts for the repair section, then to electrical diagrams..........and its FREE!

Posted on Jul 27, 2009

  • 18 Answers

SOURCE: My heater blower isn't working. Which fuse do I

the heater/ac fuse look in your owners man. it should have a diagram or give you a number.

Posted on Feb 24, 2010

Testimonial: "Thanks. I actually looked in the manual and saw a fuse listed for AC; didn't know it was the same one for the heater."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 Chevy S10 Blazer 4.3 V6 with a po154 code for oxygen sensor can someone tell me which sensor it is


O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)

Read more at: https://www.obd-codes.com/p0154
Copyright OBD-Codes.com

Jun 21, 2017 | Cars & Trucks

1 Answer

I have a 1997 Chevy s10 blazer with a 4.3 v6 will a 1998 Chevy s10 blazer 4.3 v6 interchange


they should swap just fine. 1996 and on are interchangeable. 1995 could go either way. 1994 and older are interchangeable.

Apr 23, 2016 | Chevrolet S 10 Cars & Trucks

1 Answer

1998 chevy blazer fuel pump wont shut off how do


I don't think you can on that vehicle-probably not a code, anyway. Check the fuel pump relay, it may be stuck on. Should be located in the power distribution box under hood. Pull it out-pump should stop-swap in a different relay to test. If pump still runs on with new relay, the wiring to the relay needs checked.

Sep 10, 2013 | 1998 Chevrolet Blazer

1 Answer

Can I install a 2000 Chevy 4.3 motor in my 1998 Chevy S10 Blazer, will it interchange?


The 2000 4.3 will fit in the Blazer. If the engine previously in the Blazer was a 4.3, it should be a direct changeover. Any parts differences you can use the parts off the old motor to make it work. Some connections may be different, but can be worked around.

Apr 16, 2011 | 1998 Chevrolet Blazer

1 Answer

How do u read the retrieval codes for a 93 chevy blazer s10?


If your talking about the Check engine light. You will need a CHEVROLET OBD I code reader. the auto makers used their own style of ports and language until OBD II in 1996. The code reader can be purchased at most auto parts stores and it isn't very expensive.

Dec 22, 2010 | 1993 Chevrolet S-10

1 Answer

Installing a blower motor in a 98 Chevy Blazer


96 chevy S10 p/u truck 4cyl 2.2 liter
shift solenoid electrical problem

Oct 01, 2009 | 1998 Chevrolet Blazer

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...