Question about Plymouth Cars & Trucks

1 Answer

I need the schematics for the vacuum lines on a 1992 Plymouth Sundance 2.5 engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,602 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Just_Bobz
  • 448 Answers

SOURCE: 1997 suburban vacuum line schematic

Available at dealer on request, sometimes posted on hood

Posted on Jan 07, 2009

emissionwiz
  • 76649 Answers

SOURCE: i need all the engine diagnostic codes for a 94

11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Posted on Aug 08, 2009

  • 71 Answers

SOURCE: need schematic for vacuum lines on 351 clevland

try auto zone.com they have had most of what i have had to search for .....mrdmburns@cableone.net good luck..DALE

Posted on Aug 29, 2009

  • 491 Answers

SOURCE: I need a vacuum line schematic for a 2003 chevy

Replace the complete heater control vacuum line over the motor with rubber vacuum tubing.
The heater vacuum line connects on the drivers side of the engine halfway back on the intake manifold.Run the new line to the heater vac connection at the passenger side at the right front in the engine compartment.
I change 2 a week....this should be where your problem is.

Posted on Sep 09, 2009

Testimonial: "That took care of it. I did change from that small vacuum line to the large rubber and ran it up to a wire loom overhead so as not to get as hot."

  • 60 Answers

SOURCE: looking for 1995 volvo 850 turbo vacuum line schematic diagram

This is for a 98 T5, but it should be close enough. http://www.matthewsvolvosite.com/forums/viewtopic.php?p=93956#p93956

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why going down the road to see air conditioner blow out of the defrost vents on the windshield on a 1992 Plymouth Sundance 2.5 engine


Vacuum line to the heater controll box has a leak or is disconnected.

Or the controlls went bad.

Apr 23, 2015 | Plymouth Cars & Trucks

1 Answer

What operates the doors for the air conditioner and heater controls in a 1992 Plymouth Sundance 2.5 engine


www.ask.com/1992/Plymouth/Sundance/2.5L/service-manual/
/troubleshooting-guide/
/wiring_diagrams/
/air-vent-layout/diagrams/
/door/diagrams/layouts/
/air-condition-layout-diagrams/
/ventilation diagrams/
/heat-duct-layouts-diagrams/
/what every you want or need/

Apr 23, 2015 | Plymouth Cars & Trucks

1 Answer

I have a 1992 plymouth sundance i keep hearing a grinding nosie only when i push on the gas you could hear it and when you put it in reverse now it does it while im driving pushing on gas or not i hear it


Being front wheel drive you might want to check the engine mounts. When your driving it ,the engine will move because of the torque. this is normal . If the mounts are bad it might be rattling or rubbing on something .

Nov 17, 2014 | 1992 Plymouth Sundance

1 Answer

Code 51 on a Plymouth sun dance. How do I fix it?


Code 51 = Oxygen sensor stuck in lean mixture mode. ( this will often cause engine to run rich due to oxygen sensor telling engine controller that it is running lean, thus send more fuel) This may be caused by M.A.P. sensor as well, so check vacuum lines and clean connections on MAP sensor first. It should be one of 2 things, Fault from MAP sensor, or faulty oxygen sensor.

Nov 01, 2010 | 1990 Plymouth Sundance

1 Answer

Where is the fuse box on my 1992 Plymouth Sundance? I cannot find it and need to replace the warning bell (bing) if I leave my headlights on.


You're fuse box is located under the dash, left of the
steering colum. There is also a chime module located
under the dash, to the left of the glove comp.
Also, I believe the chimes share a fuse with the brake
lights. Hope this helps.

Mar 10, 2010 | 1991 Plymouth Sundance

3 Answers

WATER PUMP LEAKING


front of the engine see picture below.

2da1ac1.jpg

Mar 09, 2010 | 1992 Plymouth Sundance

1 Answer

Diagram for an alternator belt for 92 plymouth sundance


7dc2762.gif Unsure what engine or Vin Number is for your Car. All 0f the diagrams looked the same for the 2.2 - 2.5 and others, with and with out turbo.
Hope this helps, - Jarett

Aug 17, 2009 | 1992 Plymouth Sundance

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...