Question about Cars & Trucks

1 Answer

What does the word rods mean on a scale location drawing

Looking at my location drawing for my land ,trying to go from point to point. what does 12.2 rods mean on a property drawing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,519 Answers

According to Wikipedia,
"The rod or perch or pole is a surveyors tool and unit of length equal to 51?2 yards, 161?2 feet or 1?320 of a statute mile and one-fourth of a surveyor's chain."

Posted on Apr 22, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does 12 rods mean as far as property lines


Not automotive related, but a "rod" is a unit of measure. 1 rod is 16.5 feet. So 12 rods is 198 feet long.

Apr 22, 2015 | Cars & Trucks

2 Answers

Is there way of opening my bonnet if the pull cable has snapped on my land rover


look for the cable at the hood and there might be a way with a long screw driver to push it to release it .

Jan 31, 2015 | 2002 Land Rover Freelander

1 Answer

How do you draw a tape diagram of 12 divided by 3 times 3 equal 12


Your question is in the wrong section. Look for something under math help. 12/3=4, 4x3=12 I am not sure what your teacher is looking for, but I think I would draw a circle with 12 at the top, 3 at the 3 o'clock position, a 4 at the 6 o'clock position, and a 3 at the 9 o'clock position. then put a division symbol between 12 and the 3, an = between the 3 and 4, an x between the 4 and the 3, and an = between the 3 and the 12.

Sep 12, 2014 | Cars & Trucks

1 Answer

Changed plug wires now cant start


Check for the right location by turning crankshaft till at zero degrees on the pointer scale-the timing scale. Then look at rotor position: should be either pointing to No. 1, or will be pointing directly opposite if you are on the exhaust stroke (TDC) of No. 1. Turn the crank one revolution, and come back to the zero mark. If rotor was pointed opposite before, it should now be directly at the number 1 plug wire tower.

Jan 03, 2013 | 1990 GMC Sierra

1 Answer

Location of neutral safety switch on 1994 toyota land cruiser?


It's located on the right side of the transmission where the shift selector rod attaches to the selector lever on the trans, near the front of the transmission, it also has a large electrical connector on it.

Feb 28, 2012 | 1994 Toyota Land Cruiser

1 Answer

'02 protege rod and main bearing sizes?


12 point 10mm and 12 point 12mm.

Feb 28, 2012 | 2001 Mazda Protege

2 Answers

Charging ok new battry wont hold charge 4 more than 2 days


You can start by disconnecting the battery ground cable, connect a 12 volt test lamp between the cable and the battery post, If it lights up you have a short. and you'll need to start pulling fuses one at a time until the test lamp goes out. at that point you will know where to look for short.

Mar 13, 2011 | 1998 Jeep Grand Cherokee

1 Answer

RANGE ROVER 2004 L322 DRIVER DOOR WONT OPEN FROM OUTSIDE BUT OPEN FROM INSIDE.


Hi, take the inner door panel off, look around should be a rod that goes from the outside handle to the door latch mechanism, its either broken or unhooked.
This is how i solved a similar problem. When I removed the door panel and looked inside I was able to see the small rod that attaches to the outside handle was not connected. I tried to snap it back in but it wouldn't stay so I pulled the rod over where I could see that the small plastic part on the end of the rod that holds it in place had one side snapped off. Should be easy to fix once I locate the part. Just did this today and haven't looked for the part yet.

Dec 09, 2010 | 1998 Land Rover Range Rover

2 Answers

I need the clearence measurement on tappets for land rover freelander,51 plate.Thanks Tim,Taunton


dont know what a 51 plate is ,a 51 land rover would be manual adjusters with a B series engine which would be 12 inlet and 15 exhaust .points gap would be lucas 15th and plugs would be 25th ,didnt know they used this name freelander in 1951 ,come to think of it i didnt think they made land rovers till the middle 50s

Aug 22, 2010 | Land Rover Freelander Cars & Trucks

1 Answer

12 volt DC trying to find current draw, have 0.040 on 2 amp scale . is this 40mamps


The amp reading you have is less than 1 amp. This is called 40 thousands of an amp. What system are you testing ? a amp reading this small could be for car memorie. hope this helped =)

Mar 04, 2010 | 2005 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...