Question about 2001 Hyundai Tiburon

1 Answer

Is the fuel line a compression fit? can I just pull it out without damage?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 1,326 Answers

You need a special tool

Posted on Apr 22, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Silverado pickup, I was disconnecting the fuel pump and one of the plastic connecters broke in one of the fuel lines how do I get it out.


do you mean you broke one of the special fuel pumps fitted plastic compression joins of the lines

if you cant find a mobile hose repair business that can make fitting and joins

you replace the full length of the damaged hose with a good connections ...find a wrecker ...

sil-h4yyi1plfgwlqulwpewuvgby-5-0.jpg

Apr 10, 2017 | Cars & Trucks

1 Answer

What type of hose connections are on the fuel filter box


Most cars use a special compression type fitting. The correct way to remove them is woth a fuel line removal tool. The tool is slipped onto the line and the slides into the connector releasing the retaining tabs.

Aug 11, 2016 | Cars & Trucks

1 Answer

How to disconnect fuel line for a 98 deville


YOU NEED TO GO TO AUTO PARTS STORE AND BUY FUEL LINES DISCONNECT TOOLS.THE FUEL LINE DISCONNECT TOOLS GOES IN THE MALE SIDE OF THE QUICK CONNECT FITTING.INSERT FUEL LINE DISCONNECT TOOL INTO THE FUEL LINE CONNECTER FAR ENOUGH TO RELEASE THE INNER LOCKING SPRING.AND THEN PULL OFF CONNECTOR. LUBRICATE THE MALE PIPE END WITH A FEW DROPS OF OIL.BEFORE RECONNECTING THE QUICK CONNECT FITTING. WARNING THIS IS A DANGEROUS JOB, YOU NEED A HAYNES REPAIR MANUAL TO LOOK AT PHOTOS HOW TO DISCONNECT FUEL LINES.BECAUSE IF YOU DONT DO IT CORRECTLY.AND DAMAGE FUEL LINES.YOU WILL HAVE A FIRE GAS WILL SPRAY ALL OVER THE PLACE.

May 10, 2011 | 1998 Cadillac DeVille

1 Answer

Fix or replace fuel line. i have a pin hole in the line. the car is fuel injected and i hope there is an easy repair ie: cut /n splice. because i cant see or tell were the line changes from plastic to...


Hi, if the fuel line is plastic you have to replace line. If it is the medal line go to auto parts store and by you a compression fitting and cut out bad spot and put compression fitting there, do not over tighten fitting. take a small piece of line to get the right size you need.If i can help you further just re post.

Jan 08, 2011 | 1995 Pontiac Bonneville

1 Answer

Where is the fuel filter located on a 2000 Chevy Cavalier 4cyl?


Fuel Filter REMOVAL & INSTALLATION Fig. 1: Remove the quick connect fitting from the filter 91141p82.jpg
Fig. 2: Using a 21mm back-up wrench and a 16mm wrench on the line, loosen the feed line from the filter 91141p83.jpg
Fig. 3: Carefully unthread the feed line from the filter and . . . 91141p84.jpg
Fig. 4: . . . remove the filter from the retaining bracket by pulling the filter outward 91141p85.jpg
NOTE: The vehicles covered in this manual are equipped with "Quick Connect'' fuel fittings. For more information regarding these fittings, please refer to Section 5 of this manual. An inline filter can be found in the fuel feed line attached to the rear crossmember of the vehicle. CAUTION
Before disconnecting any component of the fuel system, refer to the fuel pressure release procedures found in Section 5.
  1. Properly relieve the fuel system pressure as outlined in Section 5.
  2. Raise and safely support the vehicle with jackstands.
  3. Grasp the filter and nylon fuel line fitting on the tank-to-filter line. Twist the "quick-connect'' fitting 1?4 or a turn in each direction to loosen any dirt within the fitting. Use compressed air to blow out the dirt from the fittings at the end of the fuel filter.
  4. Detach the quick-connect fitting by pushing inward toward the filter and grasping the plastic tab around the connector and pull apart. If additional assistance is required to disconnect the fitting, tool J 38778 or equivalent can be placed between the filter and the fitting release mechanism to carefully force the two apart. Be careful not to bend the special tool. NOTE: Always use a back-up wrench anytime the fuel filter is removed or installed.
  5. Using a backup wrench (where possible) to prevent overtorquing the lines or fittings, loosen and disconnect the feed line from the filter. Be sure to position a rag in order to catch any remaining fuel which may escape when the fittings are loosened.
  6. Remove the fuel filter from the retaining bracket. To install:
  7. Before installing a new filter, apply a few drops of clean engine oil to the male tube end of the filter. This will ensure proper attachment and prevent a fuel leak.
  8. Position the filter into the retaining bracket with the directional arrow facing away from the fuel tank, towards the throttle body. NOTE: The filter has an arrow (fuel flow direction) on the side of the case, be sure to install it correctly in the system, with the arrow facing away from the fuel tank.
  9. Push the connectors on the quick-connect fitting together to cause the retaining tabs/fingers to snap into place. Pull on both ends of the connection to be sure they are secure.
  10. Connect the fuel feed line to the filter, then tighten, using a backup wrench to prevent damage, to 20-22 ft. lbs. (27-30 Nm).
  11. Carefully lower the vehicle.
  12. Connect the negative battery cable and tighten the fuel filler cap, then start the engine and check for leaks.
prev.gif next.gif

Nov 18, 2010 | 2000 Chevrolet Cavalier

1 Answer

I am trying to change fuel filter on 1995 ford econoline f-350 It appered that the fuel lines were held on by push on retaining clips but after removing the retaining clips I still cannot seem to get the...


Yes you do, The first clips you removed are the secondary clips. The lines have to be released from the inside. Heres the info.. Cobra :-)
Removal
  1. Open safety clip.

    v9067a.gif

  1. Fit Tool T90T-9550-B (5/16 inch) or T90T-9550-C (3/8 inch) to coupling so that tool can enter female fitting.

    v9068a.gif

  1. Push the tool into female fitting to release the retaining fingers from the formed male tube end.
  1. Pull male and female fittings apart.

    v9069a.gif

  1. Remove the tool from the disconnected fitting.
  1. Inspect the fitting for any internal parts that may have been damaged. Fuel tube should be replaced if internal parts are damaged.

Jun 05, 2010 | 1995 Ford Econoline

2 Answers

Need to verify the timing marks on my honda civic engine i've lined them up like it shows but the engine still turns over like it has no compression after timing the belt the cam gear has the 3 lines on it...


most honda do have interference fit engines so there is that possibility of valve damage. try a compression test on all cylinders. compare readings and note any low compression or large variations from each cylinder. Make sure to disable fuel and ignition systems by pulling the corresponding fuses. Good luck

Jan 16, 2010 | 1996 Honda Civic

1 Answer

Will 1997 tahoe fuel return line fit on a 1996 gmc yukon


Yes it should, but if your only looking to replace a small leak along the return line. Just keep it simple and section the damaged area with a rubber fuel hose. Just make sure it's a fuel injected rubber hose and no longer then 3 inched and double clamp with compression clamps. Common place to find the leak is where the fuel line is secured on the frame by the plastic clips. Good luck and keep me posted.

Jan 13, 2010 | 1997 Chevrolet Tahoe

1 Answer

Inside the tank fuel pump


You can not get to the fuel pump from inside the car. I have a 91 you have to drop the tank. BUT if you just have to. you can cut a 8in by 11in access panel in the center of the hump above the tank. You will need to use a non spark cutting tool like a air hammer. You will need 3 brass fittings 5/16 in I believe. (This is just an idea if you have to do it this way). I am not giving you this as advise. Just you could do this if you want to. Cut the hole so you can access the fuel pump from inside. You will have to cut the fuel lines one at the time. cut them in different locations from each other so the fittings will not interfere with each other. (room to fit and tighten these fittings) The fittings you will need are called compression. They are brass have small rings that fit over the line and compress to seal it. Once you cut your hole cut your lines remove the pump lines all as one part it takes a little finesse to get all out. Make a good fitting cover for your access hole and thats that. Clear as mud? this is just a (you could do it this way) but its not the right way. Drop that tank out the bottom take your rear end loose from the shocks, pull your exhaust hangers loose and let the muffler hang take the tank band loose get as much fuel out as you can. Jack the rear of the car up 3 1/2 to 4 1/2 feet to get the room needed to get the tank out. It is a tight tight fit be sure the car is secure because you will be pulling and jerking pulling and jerking to get the tank out. Work slow and careful.

Jul 03, 2009 | 1988 Chevrolet Camaro

3 Answers

Fuel filter replacement removing old filter


An inline filter can be found in the fuel feed line attached to the rear crossmember of the vehicle.

  1. Properly relieve the fuel system pressure.
  2. Raise and safely support the vehicle with jackstands.
  3. Grasp the filter and nylon fuel line fitting on the tank-to-filter line. Twist the "quick-connect'' fitting 1⁄4 or a turn in each direction to loosen any dirt within the fitting. Use compressed air to blow out the dirt from the fittings at the end of the fuel filter.
  4. Detach the quick-connect fitting by pushing inward toward the filter and grasping the plastic tab around the connector and pull apart. If additional assistance is required to disconnect the fitting, tool J 38778 or equivalent can be placed between the filter and the fitting release mechanism to carefully force the two apart. Be careful not to bend the special tool. NOTE: Always use a back-up wrench anytime the fuel filter is removed or installed.
  5. Using a backup wrench (where possible) to prevent overtorquing the lines or fittings, loosen and disconnect the feed line from the filter. Be sure to position a rag in order to catch any remaining fuel which may escape when the fittings are loosened.
  6. Remove the fuel filter from the retaining bracket. To install:
  7. Before installing a new filter, apply a few drops of clean engine oil to the male tube end of the filter. This will ensure proper attachment and prevent a fuel leak.
  8. Position the filter into the retaining bracket with the directional arrow facing away from the fuel tank, towards the throttle body. NOTE: The filter has an arrow (fuel flow direction) on the side of the case, be sure to install it correctly in the system, with the arrow facing away from the fuel tank.
  9. Push the connectors on the quick-connect fitting together to cause the retaining tabs/fingers to snap into place. Pull on both ends of the connection to be sure they are secure.
  10. Connect the fuel feed line to the filter, then tighten, using a backup wrench to prevent damage, to 20–22 ft. lbs. (27–30 Nm).
  11. Carefully lower the vehicle.
  12. Connect the negative battery cable and tighten the fuel filler cap, then start the engine and check for leaks.

Jun 28, 2009 | 1997 Pontiac Sunfire

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...