Question about 2003 Hyundai Elantra

1 Answer

Can I use jb weld around broken output shaft seal on my 2003 Hyundai elantra?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 45,552 Answers

The only fix is to replace the seal
anything else is a waste of money and oil

Posted on Apr 22, 2015

  • Josie Whitworth Apr 22, 2015

    Would it b a temporary fix at least?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: Adjusting the low beam headlight

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Posted on Jan 31, 2009

ghost4548
  • 776 Answers

SOURCE: 2003 Hyundai Elantra - diable alarm

YES!... with various system operating difference. Disconnecting the alarm does not disable it.. it only silences the alarm. You will still need the Keyless Entry System Remote to RESET the alarm to start the vehicle.

Posted on Jun 30, 2009

  • 115 Answers

SOURCE: P0139 code for a 2003 hyundai elantra. What is this code?

Hi the code P0139 is Bank 1 sensor 2 lambda sensor fault ,possible wiring or sensor fault even if you replace the sensor you need to have the MIL lamp turned off by a Diagnostic machine,it is possible you have another fault such as poor Catalytic converter efficency giving the same fault code ,Would recomend you get the car checked and read the "live" data as the car see`s it to make an accurate diagnosis and cure

Posted on Jul 10, 2009

ghost45
  • 1280 Answers

SOURCE: 2003 hyundai elantra gls abs/tcs light on

unless you can discover what DTC (Diagnostic Trouble Code) has been recorded/set in the control module, it's anyone's guess.

Posted on Sep 10, 2009

Testimonial: "thankyou"

  • 184 Answers

SOURCE: 2003 Hyundai Elantra GLS. Check engine light, code PO133

Did you use a aftermarket O2 sensor or a genuine Hyundai one? If it's an aftermarket one it may be bad or not as good as the OEM one. See here for more details and other potential causes: P0133

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could I use Jb weld on my output shaft seal for temporary use??? Would this work?


yes you could but not to long make it as smooth as possible

Apr 22, 2015 | Cars & Trucks

1 Answer

Right axle seal leaking


Can I conclude front cv shaft on the right side from your posting? If this is a yes you will have to pop the shaft out,pry the old seal out and very gently(a large socket works well) tap the new seal into place.If you are not handy I am afraid its a trip to the mechanic.Service on these is replacement only.good luck

May 07, 2014 | Hyundai Motor 2003 Elantra

1 Answer

I have a 2002 hyundai elantra and I need to change the driveaxel seal. Any one know how to change it


u have to remove wheel and lower ball join nut from nukole and nut from drive shaft from midle of hub then remove axel and seal

Nov 10, 2009 | 2001 Hyundai Elantra

1 Answer

2003 Hyundai Elantra only has 35,000kms on it! Started leaking oil really bad, took it to mechanic, he fixed the engine seal, went and picked it up, leaking oil on the way home, took it back and they tell...


dear friend-your mechanic is not very convincing,did he perhaps use a pirate seal,or incorrect seal,according the km this car is still new,so it is not posssible for crankshaft to be damaged.please get a second oppion,as it might be that the leak is from somewhere else and not the seal in question.

Nov 06, 2009 | Hyundai Motor 2003 Elantra

1 Answer

The passenger side wiper doesn't operate. Although, the bottom bolt turns when the wipers are turned on it doesn't pick up the wiper arm.


Remove the nut and purchase some epoxy ( JB weld ) mix the jb weld and apply to the spindle shaft then take the wiper arm and reattach with the nut being sure to set the arm in the correct position tighten down the nut and let dry over night or at least two to three hours at 70 degrees.

Nov 03, 2009 | 2004 Hyundai Santa Fe

1 Answer

Crank Seal Leaking


You haven't mentioned WHICH ONE? THE 'FRONT' OR THE 'REAR' SEAL? Tell you what, Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Apr 15, 2009 | Hyundai Motor 2003 Elantra

2 Answers

2003 ford ranger 2.3L engine 136000 miles


I would look for vacuum leaks before I did any parts changing

Jul 28, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
2003 Hyundai Elantra Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...