Question about Cars & Trucks

1 Answer

I hooked hot wiri to the pump and the pumpdoeswork

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 372 Answers

Check for power into and out of the fuel pump relay

Posted on Apr 22, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2000 Buick century .... its keeps running hot... I changed the thermostat.. water pump.. flushed it and it still running hot... then I removed the thermostat and its runs hot again... if I take...

I believe you have a pocket of air in your system. This happened to me before and I had all the same symptoms. I realized I was going to have to push water through the system manually to get it out. When I changed my water pump and hooked everything back up, there was no flow of coolant through the system, so I made sure when I hooked the hoses back up there was no air in them by pouring coolant into them. If that doesn't work, you can use a garden hose to force start the coolant.

Nov 23, 2014 | Cars & Trucks

1 Answer

No heat dont switch to heat

Depending on the vehicle. There are a number of things to check. First check your fuses. You may have a bad heater control, a vaccum leak (depending on make and model of car) a short in the wiri g or a bad servo that switches from cold to hot. But first let the car get to operating temperature with the heat and fan completely of after the temp gauge goes up turn the heat on hot and the fan up. If it blows hot for a few seconds then back to cold then you need a heater core flush or heater core replacement

Nov 08, 2014 | Cars & Trucks

1 Answer

An after market radio was installed poorly and dash/tail lights no longer work

if u remove the improper and go to the wire that was spliced to provide a hot to the radio you will find the culprit>

Jan 31, 2013 | 1992 Pontiac Sunbird

1 Answer

Lost wiriing descrition for coil wire type 1 VW beeyle

Hello, One hot wire from ignition switch to the ignition side of the coil. This energize the coil for starting. GB....stewbison

Aug 23, 2011 | Volkswagen Beetle Cars & Trucks

1 Answer

The engine got hot could it be the thermostat and where is it located also the water pump

Could be thermostat, follow the upper radiator hose from radiator to engine, where it hooks up at engine end, is where thermostat is at, remove small bolts at housing where hose clamps to, under that housing is where thermostat is at.Water pump, follow lower radiator hose from radiator to engine, where it hook up to, is where water pump is at.

Aug 11, 2010 | 1987 Oldsmobile Delta 88

1 Answer

Where is my fuel pump located???

It is located in the fuel tank. Use a brass punch or hardwood to keep from creating sparks when removing the retainer ring. The pump can be replaced as just the pump unit by removing the old one from the assembly once you've removed the assembly from inside the fuel tank, and reinstalling the new pump & connecting the wiring & a new filter, or as a complete assembly that just inserts into the fuel tank and plugs in to the wiriing harness once reassembled. hook up the lines & good to go. eBay has this pump & assembly available, I checked. good luck

Feb 01, 2010 | 1989 Jeep Cherokee

1 Answer

Can't find location for trailer elect hook-up

there is no factory connector you must tap into the existing wiring for brake, turn signals, tail and running lights, they make special adapters to "piggy back" into these wiries, U-Haul trailer rental can do (install and sell) this kit for u very cheap.

Jun 29, 2009 | 1998 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides