Question about Nissan Altima

1 Answer

My top right motor mount bracket is striped - Altima Nissan Cars & Trucks

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

Tap to bigger size bolt or use heli-coil

Posted on Apr 25, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a serpentine belt for a 1994 chevy corsica


Hi, to replace the serpentine belt is a bit of work, but not really that hard. You will need to take off the right front tire. Once the tire is off, you will see a "panel" with screws on it..4 or 5 i think. You will need to remove this. You will need to unhook the cables from your battery, then loosen up your alternator. You will need to take off the top motor mount. There are 2 bolts holding it to the right fender well at right top. and I beleive 3 bolts holding it to the motor mount support. You will notice a bracket right under your alternator. 2 bolts you can reach from the top, 1 bolt you will need to go up under from the bottom. There should be a "window" just to the back of where your tire goes where you can reach through to get the last bolt to the bracket. Use a wrench to raise the tension bar up, and then the belt will slip right off.

May 26, 2011 | 1994 Chevrolet Corsica

1 Answer

I have a 1992 Dodge spirit and the windshield wipers just quit working last night. We changed the fuse and that was not the problem. We think the motor might be bad. How do we replace the motor ourselves?


Wiper Motor and Linkage

Removal and Installation

1. Open hood and remove wiper arms

2. Remove cowl top plastic cover

3. Remove attaching screws or mounting nuts from pivots

4. Disconnect wiper motor wiring harness connector

5. Remove 3 motor mounting bracket-to-body bolts

6. remove motor bracket, motor and linkage assembly from cowl

7. Remove motor-to-bracket mounting bolts and remove motor

8. Reverse procedure to install

Mar 12, 2011 | 1992 Dodge Spirit

1 Answer

About how long will it take to replace the radiator?


About 2.5 hours

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

  • Tools Required
  • J 38185 Hose Clamp Pliers
Removal Procedure

110563917

Caution: Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.


  1. Remove the battery.
  2. Remove the air cleaner assembly.
  3. Drain the cooling system.
  4. Remove the right and the left engine mount struts. Refer to the following procedures:
    • Engine Mount Strut Replacement - Right
    • Engine Mount Strut Replacement - Left
    • Engine Mount Strut Replacement - Right
    • Engine Mount Strut Replacement - Left
  1. Use J 38185 to remove the inlet hose clamp from the radiator.
  2. Remove the inlet hose from the radiator.
  3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
110563918


  1. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
110563919


  1. Remove the cooling fan shroud bolts.
  2. Remove the coolant reservoir hose from the radiator overflow neck.
110563920


  1. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
  2. Disconnect the engine cooling fan motors electrical connector.
  3. Remove the cooling fan motors electrical harness from the fan shroud clips.
  4. Remove the cooling fan shroud.
  5. Remove the bolt from the condenser tube support bracket to the radiator.
  6. Use J 38185to remove the outlet hose clamp from the radiator.
  7. Remove the outlet hose from the radiator.
  8. Disconnect the transaxle oil cooler pipes from the radiator.
  9. Tilt the top of the radiator rearward.
110564721


  1. Remove the condenser hold down bracket (1) from the radiator.
  2. Remove the air deflectors from the top of the radiator.
  3. Lift the condenser from the mounting tabs on the radiator (2). Position the condenser aside.
  4. Remove the radiator.

Jan 02, 2011 | 2004 Chevrolet Impala

1 Answer

How to change the alternator on my 2000 grand voagear


This is for a 3.3L motor
Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

REMOVAL

  1. Release hood latch and open hood.
Removal/Installation of Battery Cables 81929864

  1. Disconnect battery negative cable.
  2. Remove windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  3. Remove accessory drive belt.
Generator Mounting Bracket 81929870

  1. Remove bolt holding top of generator mount bracket to engine air intake plenum.
  2. Remove bolts holding outside of generator mount bracket to generator mount plate.
  3. Remove bolt holding top of generator to mount bracket.
  4. Remove generator mount bracket from vehicle.
  5. Rotate generator toward rear dash panel.
Generator 81929868

  1. Disconnect the push-in field wire connector . from back of generator.
  2. Remove nut holding B+ wire terminal to back of generator.
  3. Separate B+ terminal from generator.
Generator Pivot Bolt 81929871

  1. Remove bolt holding bottom of generator to lower pivot bracket.
Generator 81929872

  1. Remove generator from vehicle
INSTALLATION

  1. Place generator in position on vehicle.
  2. Install bolt to hold bottom of generator to lower pivot bracket.
  3. Place B+ terminal in position on generator.
  4. Install nut to hold B+ wire terminal to back of generator.
  5. Connect the push-in field wire connector into back of generator.
  6. Rotate generator forward away from dash panel.
  7. Place generator mount bracket in position on vehicle.
  8. Install bolt to hold top of generator to mount bracket.
  9. Install bolts to hold outside of generator mount bracket to generator mount plate.
  10. Install bolt to hold top of generator mount bracket to engine air intake plenum.
  11. Install accessory drive belt.
  12. Install windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  13. Connect battery negative cable.
  14. Verify generator charge rate.

Jan 02, 2011 | 2000 Plymouth Grand Voyager

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

How to replace 1996 pontiac grand am motor mount


On 96 Grand Am 2.4L you have to remove the motor mount first to get the top 2 transaxle bolts on the mount bracket removed. The bracket and trans mount are removed as one unit after all 8 bolts are removed. You will need a 3 foot bry bar to move the engine over to the side as far as possible to make room for the 2 top bolts to be removed.

Sep 12, 2010 | 1996 Pontiac Grand Am

1 Answer

How do i replace an alt on an 97 Grand Voyager?


When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Jul 08, 2010 | 1997 Plymouth Grand Voyager

1 Answer

How hard is it to fix motor mount in 94 cadillac devillie


there are sevral as well as trans mount and the top ones that look like dog bones.and they are pretty tricky especially the bracket from the front mount its right near the headers hot hot so let it cool off

Mar 06, 2010 | 1994 Cadillac DeVille

4 Answers

I cannot get the alternater out of my 1997 Dodge Grand Caravan. It is a 6 cylindar 3.3 engine. The Chilton manual is no help at all. I have managed to remove all the bolts holding it on, but I cannot even...


3.3L & 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  5. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  6. Remove the bolt securing the top of the alternator to the mounting bracket.
  7. Remove the alternator mounting bracket from the vehicle.
  8. Rotate the alternator toward the dash panel.
  9. Unplug the push-in field wire connector from behind the alternator.
  10. Remove the B+ nut and wire from behind the alternator.
df195e7.gif
Alternator removal-3.3L and 3.8L engines


  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

LET ME KNOW IF THIS HELPED.

Oct 18, 2009 | 1997 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...