Question about 2008 Ford Territory 4.0

Open Question

How much oil does the transmission take on this vehicle including the convertor

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced transmission in 97 gmc Sierra 5.7 vortec and it is not working. I know transmission was good


Did you make sure the convertor was fully seated on the trans input shaft (3 clicks)? After trans was bolted to block, there should have been a gap between convertor and flexplate (the convertor bolts should have drawn the two together). If not, you probably wiped out the drive tangs for the trans oil pump when you started vehicle (wasn't engaged properly). Hopefully not.

Oct 16, 2015 | GMC Cars & Trucks

1 Answer

I have transmission oil leaking between the engine and transmission what could be the cause?


front pump gasket or front pump seal either way tranny will have to come out to rectify and would need to figure out what caused leakage like cracked flywheel causing torque convertor wobble could be loose torque convertor bolts but you should be able to tell that it would cause a rapping noise

Apr 14, 2015 | Cars & Trucks

1 Answer

How to remove and replace oil pan gasket on a chevy camaro 5.7 LT 1


safely raise car and support on jack stands or vehicle lift
disconnect Neg. battery cable and insulate
remove engine air duct system
remove motor mount bolts (with auto. transmission)
raise and support engine
remove exhaust/convertors
remove oil pan bolts and pan

Feb 01, 2014 | Cadillac Escalade Cars & Trucks

1 Answer

John deere problems


Have a pressure test done on the transmission to check for torque convertor /band/clutch adjustment. Check the oil cooler is not blocked from dust /dirt or other debris. Check oil level in transmission

May 25, 2013 | Cars & Trucks

1 Answer

I was driving today in my 2004 Ford Freestar van when all of a sudden the transmission stopped being engaged. I pulled over, no problem with the moter, but it would not slip back into drive reverse etc. No...


I have seen a problem with torque convertors on these vehicles, they will just all the sudden neutral out and that is it no noise no codes nothing... alot of times depending on the failure of the convertor just the convertor can be changed.... what usually happens is the splines inside of the convertor sheer off and once a new convertor is put in everything is back to normal.

May 27, 2011 | Ford Freestar Cars & Trucks

1 Answer

How to reove the torque covenrter form the transmission?


You have to remove the transmission from the vehicle, then unbolt the torque convertor from the flex plate. Once you remove the transmission you will see the torque convertor still bolted to the engine.(BIG ROUND THING)

Sep 25, 2010 | 1996 Isuzu Rodeo

1 Answer

How to instal a transmission oil pum for chevy tahoe


It involves removing the trans from the vehicle pulling the pan off the bottom of the trans removing the tcc solenoid from the pump then removing all the bolts from the pump and pulling it out the front ... chances are though if the pump is bad so is the rest of the trans .. if its just a convertor seal leaking u need to drop the trans pull the convertor pry out the old seal from the pump and replace it with new .

Mar 14, 2010 | 2002 Chevrolet Tahoe

1 Answer

Front diff oil leak


remove entire trans,remove 8 bolts and then remove front differential case at this time you will need to remove torque convertor with tube do not remove this tube from the convertor it drive the oil pump, the gasket is liquid gasket make sure surface is clean,also at this time replace torque convertor seal and seal tube this tube seperates transmission fluid from gear oil good luck

Aug 13, 2009 | 2001 Subaru Forester

1 Answer

Transmission repairs


It sounds as if there is no oil pressure in the transmission, it is possible you have no fitted the convertor correctly. if it is not fully engaged into the transmission oil pump it will not drive. of course the other thing could be the transmission has a fault. I am of course assuming you have filled the transmission with the correct type and quantity of oil. if you have pull the trans, and check the convertor has not damaged the oil pump,

Jan 21, 2009 | 2002 Mazda 626

1 Answer

1995 blazer s-10 4l60 e drive down block shifts get bad wont pull so i parked went to check for reverse and drive no reverse no drive nothing shut off start right back up and have both again ??


Presuming the fluid level is full,it is quite common for a broken reverse sun shell to give the symptoms you are experiencing,as well as some other areas that could also give similar symptoms such as burnt clutch packs,or the torque convertor going bad,and eventually the vehicle will stop pulling altogether.If the fluid is full,the problem is pretty much going to require trans removal and repair.Further diagnostic would include installing a mechanical oil pressure gauge onto the transmission to monitor main line pressure and see what it's doing while the trans is acting up and not pulling,and this does require a gauge capable of handling 300 psi.Also pull diagnostic trouble codes from the vehicle computer (PCM).Good luck.

Aug 30, 2008 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
2008 Ford Territory 4.0 Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...