Question about Cars & Trucks

1 Answer

What happens when you drill out ignition and alarm goes off on 99 crown Vic?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,585 Answers

Needs system reset

Posted on Apr 21, 2015

  • Casey Chandler
    Casey Chandler Apr 21, 2015

    Thank u...How do you reset the system?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: 99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Posted on Jul 07, 2009

co7196
  • 3433 Answers

SOURCE: 99 crown vic wont crank when i turn the key

Turn key to the run positio, Press on your brake and run your shifter through the gears a couple opf imes then try starting in neutral. This is for the benefit f the neutral safety switch. If still nothing , Raise the hood and and check the battery for a bad or corroded connection. If all is good, make sure car is in park. There is on the driverside fenderwell a relay that looks like a mine Roun With two small terminals and tw large terinals o opposite ides.. When you turn to crank, you put cirrent to one of the small ter minals and that causes the two large battery cables to connect and give power to the starter. If you can jump the battery side cable and the starter side post the starter will crank if nothing is wrong withe the starter.the two large posts. Use a jumper cable,NOT a coat hanger, iF THE STARTER SPINS THEN START IT WITH THE KEY. Good Luck.. Any more help let me know.

Posted on Nov 14, 2009

reisdos
  • 1297 Answers

SOURCE: my car keeps overheating but

since this vehicle has a thermal clutch fan I'd start there

are ALL the hoses getting hot?

  • upper rad hose
  • lower rad hose
  • heater hoses
does the overheating reduce when you turn on the heat at full speed


Posted on Jun 06, 2010

tech1969
  • 443 Answers

SOURCE: replace ignition switch in 95 crown vic

take plastic cover off bottom of column that is arund switch.there is a little pin hole where the switch is in the column on the bottom edge stick something the size of the hole in an turn switch to on position push the pin in hole and remove switch,be careful not to damage electric part on switch then put new switch in in same position as the one you removed then rotate back and forth to verify its working properly
if any question feel free to call
270-556-7357 i live in texas

Posted on Dec 25, 2010

  • 8 Answers

SOURCE: My 99 Crown Vic acts like it isn't getting gas

Was the fuel tank drained and flushed when the fuel pump was replaced? By this time it will have collected a lot of junk and gunk. Without cleaning the tank, the fuel pump will simply clog and stop working again.

Posted on Oct 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

"I have a 95 ford crown vic and the key ignition is stuck in the on position and i tried a new key ignition switch but it didn't work it was still moving freely wat is the problem now"


it sounds like the ignition cylinder has dropped a tumbler not sure of replacement procedure for ur car but it needs the ignition cylinder replaced

Jan 12, 2013 | 1995 Ford Crown Victoria

1 Answer

I have a 99 crown vic and can't seem to find the


The car is designed not to spin it's wheels when taking off. If you want to make it do that you need to either change the powertrain programming or replace some powertrain parts.

May 07, 2012 | 1999 Ford Crown Victoria

1 Answer

How to fixaciggerate lighter in 99' ford crown vic


check the fuse first, then check the connections at the back of the lighter. very basic electrical circuit

Feb 02, 2012 | 1999 Ford Crown Victoria

1 Answer

Where is the ambient air temp sensor for the 03 crown vic p71


i have a 99 crown vic suvillan and i cant find the ambient air temp sensor where is it please help

Mar 02, 2011 | 2003 Ford Crown Victoria

1 Answer

1994 ford crown vic front pass. side power window regulator...


Yes it is. They will need to be drilled out. Thats the best way, some people try to put bolts on, but I dont advise it.

May 12, 2010 | 1994 Ford Crown Victoria

1 Answer

1999 ford crown vic with ignition coils going bad a lot.


have look at ur wires that is caming from the car in to the coil it self

Mar 10, 2010 | 1999 Ford Crown Victoria

1 Answer

Lost keys - 1997 Crown Vic - How do I drill out the ignition switch?


Before you do any drilling get your vehicle identification number and call the dealership and they might be able to cut you a key.You will probably have to give them some identification to show that you own the vehicle.This would be a lot easier than drilling the lock cylinder out.Hope this helps.Good luck.

Mar 07, 2010 | 1997 Ford Crown Victoria

1 Answer

99 crown vic police interceptor steering wheel??


i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Jul 07, 2009 | 1999 Ford Crown Victoria

1 Answer

How do you test the transponder for an ignition switch


will the key go all the way in the cylinder? the transponder is the black ring thats around the cylinder, has a connector... kinda hard to explain-

May 23, 2009 | 1999 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...