Question about 2000 Buick LeSabre

1 Answer

My 2000 Buick Lesabre died while driving and now it will crank but won't start?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

1st check to see if the serpentine belt broke for the timing belt 2nd check the fuel pump by turning key a seeing if the pump makes a sound if it does that's good and 3rd if it starts a few hours and dies after a trip then your catalytic converter is clogged so put some lacquer thinner in your gas tank and fill it up and drive it around for a hour to clean out the catalytic converter

Posted on Apr 21, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 buick lesabre stall after starting or after running for 30 minutes

I have a 1996 Lesabre. I had a similar problem that slowly got worse. I brought it to two different mechanics that did diagnostic checks and could only "suggest" what to replace to fix the problem. Their problem was that it wouldnt stall out while they had the mv. After replacing a bunch of sensors and the fuel pump/ filter, I solved the problem by replacing the Crank Sensor. Its located behind the lower crank pulley on the 3.8 lt motor. Hope this helps!

Posted on Oct 29, 2008

  • 106 Answers

SOURCE: 2000 buick lesabre - water pump replacement

first disconnect the battery then check how the serpentine belt is lined up so u can take it off and put back on. Then the pump should be on the side of the motor with 9or12 bolts there could be more! after taking out take razorblad and skrap the old gasket clean wipe of then put new gasket and pump back on dont over tighten the screws cuase the pump my be aluminum.

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: My 2000 Buick lesabre cuts off while driving

Your fuel pump might be going bad. The reason why it cuts off is the fuel pump is pumping just enough to run it for a x amount of time that's why it shuts off but while it's off the pump is pumping fuel into the lines. If it's not the fuel pump then it might be your injectors.

Posted on Oct 05, 2009

  • 6 Answers

SOURCE: 2000 buick LeSabre - rear leveling system problems

The rear leveling trip switch is located on driver's side near rear air shock on the frame. Check for leaks in air line.

Posted on Oct 21, 2009

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Buick Lesabre hard start


Try depressing the gas pedal once before cranking. If it fires right up then replace the fuel filter. If not then you may need to replace the cam sensor.

Feb 20, 2013 | 2000 Buick LeSabre

1 Answer

2000 lesabre sometimes stalls at hiway speed. Temp sensor?


Have a Repair Shop Diagnose that code

Don't throw parts at it

Nov 25, 2012 | 2000 Buick LeSabre

1 Answer

How do you replace crank sensor on a 2000 buick lesabre


it is located behind the harmonic balancer. you will need a harmonic balancer puller

Oct 31, 2012 | 2000 Buick LeSabre

2 Answers

Replaced ignition module now it won't run at all


After changing the ignition module, you may have broken the communication between all the components in the anti theft security system. This is common on GM antitheft systems. Check out this link for how it works and solutions to security problems. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jun 06, 2011 | 1991 Buick Regal

1 Answer

2000 buick lesabre stall after starting or after running for 30 minutes


I have a 1996 Lesabre. I had a similar problem that slowly got worse. I brought it to two different mechanics that did diagnostic checks and could only "suggest" what to replace to fix the problem. Their problem was that it wouldnt stall out while they had the mv. After replacing a bunch of sensors and the fuel pump/ filter, I solved the problem by replacing the Crank Sensor. Its located behind the lower crank pulley on the 3.8 lt motor. Hope this helps!

Oct 21, 2008 | 2000 Buick LeSabre

3 Answers

2000 buick lesabre shuts down while driving


they have had alot of problems with key switches in that model that is where i would start

Oct 17, 2008 | 1997 Buick LeSabre

Not finding what you are looking for?
2000 Buick LeSabre Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...