Question about 2005 Nissan Altima

1 Answer

How to install the thermostat on 2005 Nissan Altima 2.5?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Nissan Expert
  • 239 Answers

This is a pretty easy repair. Your vehicle has 2 thermostats. One on the driver side of motor just below the intake manifold and the other in the center of motor just below the intake. I would flush the coolant system aswell.
Here is a link on how to do it. I have recently done one and these steps are right on.

http://www.ehow.com/how_7868154_do-replace-two-thermostats-altima.html?utm_source=eHowMobileShare&utm_medium=email&utm_campaign=MobileShareTest1

Posted on Apr 20, 2015

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 383 Answers

SOURCE: need to install a thermostat of a nissan altima

Dear Guest: If you have some reasonable mechanical aptitude, it is a simple task on this engine to do.
The thermostat is located near the front to the engine (the side closest to the belts) and on the side where the radiator is.
Follow the top radiator hose to the engine and you will have found the thermostat housing.
1. Make sure the engine is cool before doing this job.
2. Get a drain pan and drain the coolant from the radiator. The drain **** for the radiator is located at the bottom of the radiator. Some have an end which can be turned without tools and others require a flat screw driver to unscrew the fitting from the bottom of the radiator. Make sure you remove the radiator cap, as it will drain much faster. Once drained, put the drain **** back into the radiator. Be careful and DO NOT OVER TIGHTEN IT! It will snap off in the radiator!
3. Release the hose clamp which secures the hose to the thermostat housing and then grasp the hose at the neck where the clamp was and try to rotate the hose on the housing. DO NOT try to just pull the hose off. Break it loose first by rotating it on the housing. If it is stuck, get a small screw driver and carefully, slide it in between the hose and the housing, working it around until you can rotate the hose. At that point you can remove the hose and push it off to the side or take it loose at the radiator as well. CAUTION!!!!! the radiator tanks are plastic and will break if you are not careful!
4. There are 3 bolts which retain the housing to the cylinder head.
Typically the bolt head size is a 10mm. Using a 10mm socket, rotate the bolts in a counter clockwise direction, removing all three bolts. There are some that did use a 12 mm bolt head size. Most of the time the housing will just come loose. Sometimes, it will stick. If so, a light tap will break it loose. Pay attention as to how the thermostat is positioned in the cylinder head prior to removing it. Most of the time it will pop out easily or you can easily pry it out with a small screw driver. CAUTION!!!!
Do not damage the mating surface where the gasket seals.
Carefully clean the old gasket off. A single edge razor works fine.
5. The thermostat has a top and a bottom. If you look closely, you will see a place in the outer parameter of the thermostat where there is a small hole, often with a little metal tab which projects through the other side and is able to jiggle some. This is a small bleeder to help bleed the air trapped in the system when it is installed. This part of the thermostat must be at the 12:00 position.
Additionally, make sure the part with the hoop is sticking out toward you. The cylinder head has been machined to allow the thermostat to fit flush with it when installed properly.
6. Clean the old gasket from the thermostat housing. Nissan utilizes a liquid gasket sealer (silicon) which you apply a "SMALL" bead around the water inlet (the cylinder head side), let the sealer skin lightly and then put the housing in place making sure that the thermostat had remained seated during the installation. If it had come loose and you try to tighten the bolts, you will crack the thermostat housing.
7. When you tighten the thermostat housing bolts, there is a torque specification however most people don't have torque wrenches which measure in inch pounds. For those who have a torque wrench, 10mm bolts:56.4-66 inch lbs, 12mm bolts 12-14 ft lbs.
I have found that the easiest way to keep from over tightening the bolts is to grab the ratchet from the head and tighten the bolts because you don't have the leverage at that point.
8. Let the silicon dry for 10 minutes and and then fill the system back up with coolant. Reattach the hose and clamp being careful not to over tighten the hose clamp.
If you are replacing it, not more than a 50/50 mix. There is no special bleeding procedure Nissan has for this car. Just fill the radiator with coolant, turn the heater inside the car to the heat position to allow coolant flow into it as well, because it too is part of the cooling system in terms of coolant capacity. I usually fill the radiator until it shows 1/2 way up the tank. As the engine warms up,prior to the thermostat opening, more often than not, the coolant level will rise dramatically before it drops. Once the thermostats has opened top the system off, put the cap on and let it run for a while and watch for leaks. Take the car on a short loop and then recheck for leaks again. If everything has gone well, the temperature will read normal and no coolant will be leaking.
Hopefully this should be sufficient to answer your question.

Posted on Apr 05, 2009

  • 268 Answers

SOURCE: 96 nissan altima with ne water pump and thermostat

1. Improper water circulation: Sometimes, eventhough you are sure that you have enough water on your radiator, your car still overheats. It might probably be that the water is cannot circulate properly, which results to improper cooling process. There are several reasons for this which you can discover by yourself. To verify if the water circulates properly, start your engine without the radiator cap. If water circulation is good, you should notice that the water pops smoothly over the top but still retains the amount. Another way to check, detach one of the ends of your radiator hose from your radiator and see if water flows continously over.
If water doesn’t circulates well, check the thermostat if it’s open. It should be open, meaning clean, and the water can pass through it.
If thermostat is clean and still the water doesn’t circulate properly, then you have to check the water pump. That’s probably where the problem is. A little leak on the pump will cause improper flow of water through the radiator system.
If you are sure that the problem is not about water circulation, another thing you can consider is check the engine oil. Very low amount of oil can cause greater friction of the mechanical system of your engine. If it’s not time to change oil yet, you can add over some amount of oil until advisable amount is reached.
While we can’t be always sure about our engine, especially if it’s not new, we should be prepared when it happens. Bringing extra gallon of water in your trunk will surely help.

Posted on Jul 29, 2010

triple_cg_95
  • 12 Answers

SOURCE: Were do I find the thermostat on my 1994 nissan altima to replace it?

Here is a diagram showing where the thermostat is located on a 1994 Nissan Altima. Most vehicles are fairly similar as well the main water hose that goes to the engine is usually right next to or attached to the thermostat housing. Also once you take this hose off to get the thermostat you are going to need the bleed the coolant system because there will be air in the system. A simple google search or wikihow will show you exactly how to bleed air out with pictures and simple instructions. Good luck.
25287090-15uk5heqgoha5mc4ejw3dmql-3-2.jpg

Posted on Nov 17, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show a diagram for replacing a thermostat on a nissan altima 2005


Today is your lucky day Michelle,here's a link to replace your thermostat,need more help,let me know,k. Repair Guides Thermostat Removal Installation AutoZone com

Jan 12, 2014 | 2005 Nissan Altima

1 Answer

2005 Nissan Altima heat problems


You may have a thermostat stuck open,Have it replaced.on older cars the thermostat would stick shut and people would burn up there engines.Now they make them stay open when they fail so you dont overheat your engine and blow it up..

Feb 17, 2013 | 2005 Nissan Altima 2.5

2 Answers

My 2005 nissan altima has no heat


If before you change the thermostat,if the car has always had that thermostat in it,and the heater heated before and the engine is not overheating,the thermostat is most likely fine.But that is the cheapest way to start,Lissa is on the right track there.The heating element may need replaced..

Nov 29, 2012 | 2005 Nissan Altima

2 Answers

NISSAN ALTIMA '05 NO HEAT AT IDLE HEAT WHEN MOVING


I'm having the same problem, no heat at idle. I replaced the waterpump/both thermostats/belt and radiator. I'm still having the same problem. any ideas?

Thanks,

Kurt

Jan 27, 2010 | 2005 Nissan Altima

2 Answers

How to replace front airbag sensor on 2005 nissan altima


1 First remove Both Positive and negitive battery terminals. wait atleast 3 minutes.
2 Remove front grille
3 Disconnect crash sensor Plug.Crash sensor is just below the hood latch.
4Remove crash sensor retaining nuts.
5 Remove crash sensor.
Installation is the reverse order

Sep 25, 2009 | 2005 Nissan Altima

1 Answer

How do I replace the alternator on a 2005 Nissan Altima?


first things you have to do to change nissan altima 2.5 alternator?
1- disconnect battery
2-from the top of alternator there will be 3 thing u have to open one is with bolt 12 mm and second is with screw star.
3-turn the starting full right there will be small cover 2 plastic clip and one 10 mm bolt.
4-from the down take 12 mm and turn the pulley which is bellow alternator with press.
5- take belt out (note that u have to draw the map of belt be4 take it out.
6-and install alternator back again in same steps.

Dec 26, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...