Question about 2005 Chrysler Crossfire

Open Question

Chrsyler crossfire headlights are shinning outward. Happen after installing new one.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a headlight out on the drivers side of my 2005 chrsyler pacifica. I replaced the bulb but still doesn't work.


First test the bulb socket, use a 12 volt test light, the socket may be defective. Make sure you have 12 volts and a good ground.

Jul 24, 2017 | Cars & Trucks

1 Answer

Can the 2005 Chrysler Crossfire Limited Coupe automatically turn on the low beam head lamps at night?


No. It has auto lamps.all newer vehicles have them. Some you can turn off. You have to have the light switch in the dash. If it is in the turn signal switch/ column. Your out of luck.

Dec 04, 2014 | 2005 Chrysler Crossfire

1 Answer

Need to re place the broken riht headlight


If you don't replace your own headlight, you'll pay big (comparatively) at the shop. I search an article to teach you on how to replace your bulb. visit this article.


for long lasting motorcycle tires, use Cheng Shin Motorcycle Tires

Mar 05, 2013 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

How do I remove the headlight cover from 2005 crossfire to clean the precipitation


they are sealed units and not meant to be taken apart, if there is moisture inside it means there is a crack or hole somewhere allowing it in, look for anywhere moisture can get in and seal it, the moisture that is there now will dry up over time.

Oct 14, 2012 | 2005 Chrysler Crossfire

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

Need to replace headlight?


  • Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  • 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  • 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  • 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight I would replace them both sides if i were you
  • Dec 02, 2010 | 2004 Chrysler Crossfire

    1 Answer

    How to replace head light


    The headlight replacement procedure.:---
  • Apply the parking brake and open the hood.The head is attached by thumb shaped screw.You will see the thumb screw on the upper inboard corner of the turn signal assembly Remove the screw with the screwdriver.Pull the turn signal assembly outward away from the fender and then disconnect the bulb.Turning the socket and wire 1/4- counterclockwise. Set the turn signal assembly aside.Disconnect the electrical connector plug from the headlight being replaced. Lift up on the blue retaining clip of the plug and pull it away from the socket of the headlight.Turn the black retaining collar of the headlight counterclockwise to remove it and the headlight from the headlight assembly.Install the new headlight by reversing the procedure.Replace the turn signal bulb into its assembly and reinstall the assembly and thumbscrew.

    Thanks.Helpmech.



  • Nov 12, 2010 | 2005 Pontiac Montana SV6

    1 Answer

    Installed new low beam headlight and light will


    Hi, if you have a meter to check the bulb, use it to check the wiring to the socket or wiring for power when light switch is turned on. You should have around 12 volts depending on year and type of truck or auto. If the old bulb was burned, you should have power there. When you turn on switch, the other side should work and you will know you have power and it may just be corroded. Check this and you should find the problem. Please keep me posted on this, I will be around to help you. Please rate me kindly if I have been of help to you.
    Sincerely,
    Shastalaker7

    Jul 06, 2010 | Chrysler Town and Country Cars & Trucks

    2 Answers

    HOW TO TURN THE FOG LIGHTS ON


    First you have to turn the headlight switch all the way to the right. This will turn on your headlights. Then pull the switch outward towards you. Your driving lights should be on now. They only work with the headlights on.

    Apr 30, 2010 | 1996 Dodge Intrepid

    1 Answer

    Right hand side headlight doesn't come on. ive checked all fuses and installed a new headlight bulb but the light still doesn't come on. the only other problem i could think of is a wiring fault. any i...


    I had a simialar problem with a Chryser crossfire, I checked the fuses and replaced the globes, even to the extent of pulling out the whole headlight. I rechecked the fuses and found that there were seperate fuses for left and right, I kicked myself because the right had blown. just check it again, also I have in the past bought a new globe that was faulty, use a circuit tester to test the plug to be sure. Good luck

    Nov 19, 2009 | 2004 Honda Civic

    Not finding what you are looking for?
    2005 Chrysler Crossfire Logo

    Related Topics:

    31 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8210 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...