Question about Cars & Trucks

Open Question

How do I tighten the power steering belt on a 3500 Vandura van?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 80668 Answers

SOURCE: how to install power steering belt on 97 geo prizm

Most likely the belt and pulleys are shiny if you look at them, replace the belt, while you have the belt off try and clean the glaze off the pulley groves, this will make the new belt "grip" better and avoid slipage.

Posted on Aug 27, 2008

Ad
  • 275 Answers

SOURCE: trying to replace the serpentine belt on a 1995 gmc van

you will have to get ahold of a book for it or go to a junkyard and find one like yours and get the belt routing decal

Posted on Nov 12, 2008

greg_margo
  • 1959 Answers

SOURCE: Power steering belt diagram needed

Below is the diagram you requested. The drive belt also drives the power steering pump.
5bdff5c.gif

Posted on Oct 30, 2009

Testimonial: "Thanks a lot, exactly what I needed!"

drsinister69
  • 2317 Answers

SOURCE: how to tighten power steering belt on 1990 vw jetta

You have to get to it from under the car. Remove the plastic cover piece. There are 5 bolts that need to be loosed to tighten the belt. The bolt at the top of the bracket, the two pivot bolts going into the pump, 1 bolt that is up in the rear bracket of the pump, (bracket bolts to the block) and the bolt that holds the tensioning adjusting bolt on the front of the pump bracket. Turning the long bolt adjusts the position of the pump. All bolts should be 13mm head bolts. The "hidden" bolt on the back bracket xan be reached by using a deep well 13mm socket and a 3 inch extension. The others with a wrench or socket.

Posted on Mar 14, 2010

  • 113 Answers

SOURCE: Which belt on a 2003

bubbamsr.gifHere is a diagram for your belts the power steering belt is the one that broke the tensioner will need to be loosened to install a new belt. depending on your mechanical ability you should be able to handle this job. hope this helps

Posted on Feb 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3500 vandura conversions van , 1 ton wit 3/4 ton calipers 5 lugs. Changed breaks but when I break then let off it like jerks hard to the rite.


you might have to have an alignment done. Or there could be something wrong with the brake drum, or the parts became damaged.

Nov 06, 2017 | Cars & Trucks

1 Answer

Put in new power steering pump and still whining 1997 astro


My personal suggestion would be to go for these repair catalogs. I know this website reliable-store.com that I used to
buy them from, and they have online it was very good manual. Go ahead, I bet.

Mar 05, 2018 | Chevrolet Astro Cars & Trucks

1 Answer

93 gmc vandura 3500 box van won't start. I have power, installed new starter and ignition switch, but the starter won't kick.


Some vehicles Red (hot lead) have an inline fuse. Also check for other fuses for the ignition. If you have an alarm system, make sure it is disarmed. That can be done by using the key to open the down some times.

Oct 24, 2013 | 1984 GMC VanDura

1 Answer

How do you tighten the power steering belt on a 93 Dodge Caravan?


There is no adjustment you have a tenshioner if its bad you must replace it.

Apr 18, 2013 | 1993 Dodge Caravan

1 Answer

What does this style van weigh


Hi,

This depends on if it is a 1500 - 2500 - 3500 these are also the weights of the vehicle. 1500 = 1.5 ton etc.

Hope this helps.

Thanks

Jason

Oct 20, 2010 | 1984 GMC VanDura

2 Answers

Lots of play in steering column of a 1990 GMC


Where is the play coming from? Won't be the steering column,you just notice it there.

Oct 01, 2009 | 1992 GMC Sonoma

1 Answer

Need serpentine belt sequence


try this website to see if they have your car listed its www.autozone.com and there should be a diagram under the hood telling you how the belts go and try this website as well its www.alldatadiy.com i also would like to give you this information if you ever have any hard to find GM-part its Schram auto & truck parts they sells only Gm- 1-800-292-1032 and they website is www.schramauto.com and i hope i have been some help to you Michigan Man

May 20, 2009 | 1984 GMC VanDura

2 Answers

Can't get A/C belt around pulleys on my 01 Chevy Tracker 2.5 V6



Removal & Installation

1.6L Engine
A/C Compressor Belt
  1. Disconnect the negative battery cable.
  2. Loosen the A/C compressor mounting bolts.
  3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
  4. Remove the A/C compressor drive belt from the pulleys.

To install:
  1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
  2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
  4. Connect the negative battery cable.

Alternator Belt
  1. Disconnect the negative battery cable.
  2. Remove the power steering pump and the A/C compressor drive belt.
  3. Loosen the generator mounting bolts.
  4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:
  1. Properly route and install the generator drive belt on the pulleys.
  2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
  3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
  4. Install the power steering and the A/C compressor drive belt.
  5. Connect the negative battery cable.

Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Loosen the power steering pump mounting bolts.
  3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
  4. Remove the power steering pump drive belt from the pulleys.

To install:
  1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
  2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
  4. Connect the negative battery cable.

Apr 26, 2009 | 2001 Chevrolet Tracker

2 Answers

Why does my van squeel


You didn't say what type of pump was replaced, water, power steering, or ??? 
If it was the power steering pump you may be low on fluid or the belt is not tight enough. If it was the water pump it still may be the power steering belt was not tighten enough.
Go to www.youtube.com, type in power steering belt and select the appropriate video and it will show you how.

Mar 06, 2009 | 1998 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...