Question about 2006 Chrysler Pacifica

1 Answer

There is something lookalike Small blue motor under & behind the gear stick what is that???

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 752 Answers

Hi Im AL the owner of Big As Auto Repair.

If you are talking about the motor that's mounted to the back of the gear shift housing, that is the release motor that allows you to take it out of park. If that motor has gone bad then you will not be able to take it out of park. If that's the case you'll need the gear shift assembly. For further assistance go here: http://www.bigasautorepair.com/

Posted on May 04, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 manual subaru forrester will not shift in reverse


Assuming you can press the clutch and EASILY select fwd gears, then I'd suspect either
* the linkage from the gear stick to the transmission is being jammed / obstructed by something under the car.
* something in the center console is jamming the stick getting in to reverse.

If you can't easily select fwd gears, check the clutch slave and master cylinders.

Jun 09, 2014 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

1991 Toyota celica turns over but wont crank


If you can hear something turning but your engine is not cranking over either your drive gear on your starter motor is sticking and not engaging or your starter drive and/or flywheel ring gear teeth are worn away. Remove your starter motor and chech the drive gear can be moved. If ti is sticking wind it down and spray it with wd40. Don't be tempted to put grease on it. If it is a pre-engaged motor it could be gear wear or sticking mechanism.

May 17, 2012 | 1991 Toyota Celica

1 Answer

How do I change the IG1 relay on a 2002 Toyota Camry


I didn't see the actual answer to your question...but here you are. It's on the backside of the fuse panel under the driver's side dash. You'll have to stick your head up by the brake pedal, and the relay panel will be up to your right. You'll see 4 small relays, and the grey relays (for the IG1 relay and rear defroster relay) behind the blue ones. I'd suggest disconnecting the battery to ensure you don't accidentally short something out when you pry the relays out of the sockets. Good luck!

Jan 21, 2012 | 2002 Toyota Camry

1 Answer

How do you remove the radio out of a honda civic


good day Sir, In order to gain access to the rear of the stereo for either connection to, or replacement of the factory unit, you must first remove the panel surrounding the (manual) gear stick. This should not be attempted with any form of 'level' to avoid damage to the dash finish. To remove the surround simply press fingers into the gear gaiter to gain purchase behind the panel and firmly 'pull' the panel toward you to disengage from the clips that hold it in place. The main panel above requires removal which involves location and loosening (not necessarily removal) of two hex headed screws approximately 6 inches (150mm) down from the head unit behind the panel, which screw the vertical metal plates holding the panel to the under dash mountings. To gain access to the screws push the two stops on the glove box inwards to allow the glove box to swing downwards. On the other side remove the small panel under the steering column Once loosened, the entire stereo/ heater control panel may be pulled toward you to disengage the clips that hold it in position. Reassembly is the reverse of removal, ensuring that the screw slots are properly engaged before final tightening of screws and reinstallation of gear stick surround.i hope this will help you

Jul 07, 2010 | 2002 Honda Civic

1 Answer

Need to replace computer but cant find it


dealer only as it needs resetting and programme

Nov 26, 2008 | 1994 Hyundai Excel

Not finding what you are looking for?
2006 Chrysler Pacifica Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...