Question about Jeep Cars & Trucks

1 Answer

Okay so I need help replacing a cam shaft sensor on a jeep grand Cherokee 5.7 hemi engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

What kind of help?
what year GC, (usa or export)

Posted on Apr 20, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Jeep Hesitates. P0303 code

Check the cylinders Commpression. over 115 psi is good, 120 psi is normal.

Posted on Sep 17, 2008

  • 1 Answer

SOURCE: 2005 Jeep Grand Cherokee (HEMI) Service Electric Brake System

Problem is a faulty Steering Angle Sensor (part of Steering Module) located in steering column ...replacement part $600.00.

Posted on Apr 16, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

ZJLimited
  • 17970 Answers

SOURCE: where to replace coolant temp sensor for 1998 grand jeep cherokee

Check this image...

b33c4b0.png

...in the Section ZJ-Secc-8D-Ignition-Systems (page 5, fig. 10 and 11).

Good luck.



Posted on Sep 07, 2009

emissionwiz
  • 80417 Answers

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Posted on Jul 21, 2010

Testimonial: "that is just what i needed thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will my 2014 grand cherokee hemi easily tow a 4k pound trailer?


yes easily

Which 2017 Jeep Grand Cherokee engine tows the most?
Engine - Max. towing capacity
3.6L Pentastar VVT V-63,265 kg (7,200 lb)
3.0L EcoDiesel V-62,812 kg (6,200 lb)
5.7L HEMI VVT V-83,265 kg (7,200 lb)
6.4L SRT HEMI V-83,265 kg (7,200 lb)

2017 Jeep Grand Cherokee towing capacity

Mar 24, 2018 | Jeep Grand Cherokee Cars & Trucks

1 Answer

2008 Jeep Grand Cherokee Limited 5.7 Hemi Check engine light on, code P0750


2008 jeep cherokee (hemi) engine light its on i brought to fix they change 4 sensor and the converter. After 5 days engine light comes on again, what else can be? im depress about it, after paying almost 2 grand to fix this issue.

Jan 25, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Engine light came on...reading states its my cam shaft sensor, but dealer states 1997 grand cherokees 6 cyl. dont have a cam shaft sensor...What can it be then? if reading staes its a cam shaft?


Your cam sensor is inside the distributor. Problem is they list it as a Stator, not a sensor. on newer models, the sensor replaces the entire distributor. To remove it, you need to take the distributor out of the engine and remove the center shaft etc.

Apr 12, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Need to change the starter on a 2008 jeep grand cherokee limited with a v8 hemi. Found the starter but not sure how to get it out. Do I need to remove the exhaust or drive shaft? Thanks for your help.


Same issue. 2008 Grand with Hemi. loos like the Driveshaft has to come out but I still do not know if there is enough Wire length to get the wires off with the starter unbolted

Dec 09, 2010 | 2006 Jeep Grand Cherokee

2 Answers

01 Jeep grand cherokee laredo won't start. No fire is going to engine. Changed spark plugs but didn't help at all


you might want to check you cam shaft sensor amd also there is a different sensor under the distutor i had to replace both of these on my 95 jeep grand cherokee laredo

Dec 04, 2010 | 2001 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

2 Answers

2005 Jeep Grand Cherokee (HEMI) Service Electric Brake System


Problem is a faulty Steering Angle Sensor (part of Steering Module) located in steering column ...replacement part $600.00.

Apr 14, 2009 | 2005 Jeep Grand Cherokee

1 Answer

1993 jeep grand cherokee


Try replacing the crank sensor on the transmission bell housing

Sep 28, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...