Question about 1995 Chevrolet Suburban

1 Answer

How to turn abs light off on 1995 chev.sub

Abs light came on, change brake pads, light stillon.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 242 Answers

IT IS PROBABLY A BAD SENSOR YOU NEED TO HOOK IT UP TO A COMPUTER TO FIND OUT WITCH ONE

Posted on Jun 10, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Richie_asg1
  • 1036 Answers

SOURCE: replace brake pads on chev. colorado pick-up

90% of the time the sequence is identical.

Slacken wheelnuts.
Jack up and support on axle stand.
Remove roadwheel.

There should be two bolts holding the brake caliper on - usually on the inside.
Slacken both, but only remove the lower one.
The caliper should then be able to swing up pivoting on the top bolt.
You can remove this top bolt, but support the weight of the assembly with wire to the suspension spring - so as not to stress the brake hose.
Remove the brake pads, and clean the areas the pads seat on.

Push back the pistons. Some require a special tool, most make do with a wooden packer and suitable large lever - or G clamp.

Fit new pads. Pay particular attention to any fitting clips, springs, rods or pins that are needed.

With new pads in, swing down caliper into position. Fit new attatchment bolts or use a threadlock on fixings. & tighten.

Still with wheel off, depress brake pedal to activate brakes - & check for leaks and working.
With foot off brake, check hub turns with no problems.
Refit wheel and repeat for other side.

ALWAYS replace brakes in axle pairs.

Hope this helps.

Posted on Jun 14, 2008

bbtoast
  • 319 Answers

SOURCE: 95 sub emerg/parking brake light will not turn off

Only two things should normally activate the light:

Parking Brake engaged switch.

Low Fluid level in master cylinder.

I don't think you did any work to the Parking brake, but you should check it to be sure.

I believe that you would have double checked the fluid level, but please check it again.

Other things that could activate the light would be a worn or leaking master cylinder; improper brake fluid type; a damaged brake booster diphragm .

I have attached a link with excellent info on how a brake system works here.

Also, does the light always stay on, or only when you apply the brakes?

Brian

Posted on Jun 25, 2008

  • 90 Answers

SOURCE: abs light

This is a (4) four wheel sensor system and more than likely one of them has failed. This will cause ABS module to turn on warning lamp and make the brake pedal 'act up' under the right conditions.This 'acting up' is the ABS system getting a false signal that a wheel is not turning the same as the others when it actually is. Have it scanned for codes and a streaming data scan on a road test under the same conditions that you are experiencing the 'act up' to pinpoint the fault. Hope this helps! Please rate me.

Posted on Jan 31, 2009

  • 2 Answers

SOURCE: ABS light would come on

This is your Hub Wheel Assembly. Just replace them, get an alignment, and you will be set to go. I have had to replace mine twice in 5 years so they seem to go out relatively quickly in the Blazer. Good luck!

Posted on Jul 27, 2009

  • 13 Answers

SOURCE: ABS and Traction Control Light On

Because the brakes were changed, either one of the sensors were broken when removing brakes or it has set a code. Go to your local autoparts store and have them reset the code. See if it comes back on. If it does you will need to look at the ABS sensors on each wheel and replace if damaged

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am changing the front brakes on my 1995 Chev. S-10 (with ABS) When I changed the pads and put the caliper back on, and pumped the pedal to bleed the brakes, it seemed to have locked the brakes. Is...


Unfortunately it takes special equipment to bleed the brakes on a vehicle with ABS brakes. If you can get the car to a shop it's best to have them bleed the air out of the system.

Feb 21, 2011 | Chevrolet S 10 Cars & Trucks

2 Answers

Brake light and abs light on


this means that one of you abs wheel sensors is not working take voltmeter check each wheel senser there on the caliper around it should be 12 volts then check fluid cause brake fluid set off brake light too but those only two possibilitys

Sep 14, 2010 | 1995 Chevrolet Caprice Classic

1 Answer

I changed the brake pads on a 05 equinox


Did you bump the ABS pickup at the wheel hub when you changed the brakes? Or are the wires maybe nicked? The noise is normal and might go away depending on the brake pad type you replaced with. The ABS problem might be caused by you.

Nov 24, 2009 | 2005 Chevrolet Equinox

1 Answer

1995 dodge neon below 10mph foot on the brakes the abs noise no light it sounds like a drinding noise


Brake pads are worn out. The ABS light would not come on because there is nothing wrong with the ABS. The grinding you are hearing are the brake pad backing plates rubbing against the rotor. You should have heard a high pitched squeal long before this happened. More than likely the rotors are now destroyed and will need replacing or at the very least turned in a machine shop. Fix this yesterday.

Nov 23, 2009 | Dodge Neon Cars & Trucks

1 Answer

ABS and Traction Control Light On


Because the brakes were changed, either one of the sensors were broken when removing brakes or it has set a code. Go to your local autoparts store and have them reset the code. See if it comes back on. If it does you will need to look at the ABS sensors on each wheel and replace if damaged

Sep 29, 2009 | 2005 Chevrolet Equinox

1 Answer

Changed brake pads and fluid. Brake light/ABS light still lit.


Go back around and check to make sure you didnt accidentally pinch or cut a brake pad sensor. Also the ABS modules on VAG cars are pretty crappy.

Sep 11, 2009 | 1999 Audi A4

1 Answer

Anti lock brake light on dash in 1995 gm yukon


sounds to me like the abs relay is bad maybe $75 repair at the dealer

May 04, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Abs light keeps coming on audi 80 1995


looks like you have a faulty sensor (ABS) check all conections on hubs you may have disturbed something when you changed your brakes hope this helps

Jan 26, 2009 | 1992 Audi 80

Not finding what you are looking for?
1995 Chevrolet Suburban Logo

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...