Question about Volkswagen Cars & Trucks

1 Answer

Where is the fuse that control a 2006 vw windshield wiper?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 98 Answers

I just googled 2006 vw windshield wiper fuse and got a lot of diagrams for a lot of different vw's. What model is it if you need more help I will try to help ya.

Posted on Apr 20, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2006 Tucson - windshield wipers not working

check wiper motor and its connections. Fuse box not labeled very well check each fuse

Posted on Dec 17, 2008

emissionwiz
  • 76164 Answers

SOURCE: windshield wipers

From your owners manual:

Fuse#11 30A , Wiper Run/Park
Relay, Wiper Hi/LO Relay, Windshield Wiper
Motor, Rear Washer Pump Relay

U will also need to check the relays if the fuse is ok, the relay, it is the underhood fuse box
Relay #202 — Front Wiper Run/Park Relay

Posted on Dec 18, 2008

Molson02536
  • 3854 Answers

SOURCE: 2006 kia wipper works but stops in the middle of the windshield

It sounds like the the circuit board has gone bad and does not know where the base is any more so it will stop at the middle or the windshield. Auto Zone should have a new board if it's replaceable like the GM products. Good luck and hope this helps, In the mean time you can always turn your wipers on and pull the fuse out when it's at the down position so it's not up.

Posted on Jul 11, 2009

  • 432 Answers

SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control

May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Posted on Feb 05, 2010

steve_e_uk
  • 1675 Answers

SOURCE: 2000 VW jetta VR6 windshield wipers wont work

first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong


Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

Sep 05, 2017 | Cadillac Cars & Trucks

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

2006 vw jetta wiper still not working after changing the wiper motor and wiper switch ? help


Did you check the fuse? Have power at the plug? could be a bad ground.

Dec 06, 2015 | Evan Cars & Trucks

1 Answer

What has caused the windshield wipers and washers to quit working on my 2006 VW Jetta TDI


First thing I would check is the fuse for the wipers. That's usually the problem

Nov 24, 2014 | 2006 Volkswagen Jetta

2 Answers

Windshield wipers will not shut off. what is the problem. i also pulled every fuse that said something about the wipers and they still run. what fuse number is it.


My fuse # is 19 and it's under the back seat. Also, I fixed my constantly on wipers by replacing the entire wiper motor. I believe that the actual problem is the module but that item does not come alone and one must purchase the entire motor. The dealer priced me at $150 but I got one at Autozone for $100 with a $30 refund once I returned the old one (core), so total price was $70.
Hope this helps.....

Feb 02, 2011 | 2006 Chevrolet Trailblazer

1 Answer

Front Windshield wipers do not turn on


better diagnostic with scanner in body control mode there its posible to test wiper relay,motor ectr,its better than be replacing parts,

Nov 23, 2009 | 2006 Dodge Magnum

1 Answer

Windshield wipers on 2001 VW Golf move very slowly


its either the windsheild wiper switch, or the wiper moter....

Jul 23, 2009 | 2001 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...