Question about 1994 Pontiac Grand Am

1 Answer

How do I remove the rear brake cylinder?

The brake line has been detached. The two screws that hold the cylinder in place have also been removed. There does not seem to be enough room between the hub and the wheel assembly to slide it out. I have removed the bleeder valve, but it is still stuck. What else am I supposed to do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 14,333 Answers

Here's a link to your rear wheel cylinder replacement guide. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

Posted on Apr 19, 2015

Testimonial: "Get the spam out of here."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i change the rear brake cylinder


remove wheel in drum
remove springs.
and shoes.
remove screw to slave
remove slave. cylinder,
or go to alldata.com and read. its all there.

Aug 31, 2013 | 1996 Geo Metro

1 Answer

How do you change rear drum brake shoes on a 1999 couger.


SECTION 206-02: Drum Brake 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/14/2001 Brake Shoes Removal
  1. Loosen the wheel nuts.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the wheel.
  1. Release the brake shoe automatic adjuster.
    v1201041.jpg
  1. Remove the brake drum.
    1. Remove the retainers (if equipped).
    1. Remove the drum.
    v1201040.jpg
  1. Make sure that the hub flange is in the correct position as shown.
    v1201042.jpg
  1. Remove the hold down springs.
    m1201030.jpg
  1. Disconnect the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Disconnect the cable from the secondary shoe.
    v1201043.jpg
  1. Disconnect the shoes from the anchor block.
    1. Disconnect the shoes from the anchor block.
    1. Remove the lower return spring.
    v1201044.jpg
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Detach the shoes from the wheel cylinder.
    v1201045.jpg
  1. Hold the wheel cylinder pistons in place with a rubber band.
  1. Remove the upper return spring.
    v1201047.jpg
  1. Remove the primary shoe from the strut and brake shoe adjuster.
    1. Rotate the adjuster counterclockwise.
    1. Remove the primary shoe.
    v1201048.jpg
  1. ani_caut.gif CAUTION: Take care as the strut support spring is under tension.
    Detach the secondary shoe from the strut support.
    • Detach the strut from the shoe by levering the strut against the shoe.
    v1201049.jpg
  1. Remove the parking brake return spring.
    v1201050.jpg
Installation
NOTE: Install new shoes as axle sets.
  1. Clean, check and apply Silicon Dielectric Compound D742-18A331-A or equivalent meeting Ford specification ESA-M1C171-A to the backing plate contact points.
    v1201051.jpg
  1. Install the parking brake return spring.
    v1201050.jpg
  1. Install the secondary shoe to the strut and brake shoe adjuster.
    v1201052.jpg
  1. Install the primary shoe to the strut and brake shoe adjuster.
    1. Install the primary shoe.
    1. Rotate the adjuster fully clockwise.
    v1201053.jpg
  1. Install the upper return spring.
    v1201047.jpg
  1. Remove the rubber band holding the wheel cylinder pistons in place.
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Position the shoes to the wheel cylinder.
    v1201140.jpg
  1. Position the shoes to the anchor block.
    1. Install the lower return spring.
    1. Position the shoes to the anchor block.
    v1201141.jpg
  1. Install the hold down springs.
    v1201142.jpg
  1. Install the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Install the cable to the secondary shoe.
    v1201043.jpg
  1. Install the brake drum.
    1. Install the drum.
    1. Install the retainers (if equipped).
    v1201143.jpg
  1. Install the wheel.
    v1501127.jpg
  1. Operate the brake pedal to achieve automatic adjustment.

2010&c18=modelyear&c20=g167866&c35=wsm%2cbrake%20shoes%2csxu%2c206-02%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 1999 Mercury Cougar

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

1 Answer

Replacing the rear drum brakes cylinder


remove upper shoe return springs, loosen but do not remove brake line using line wrench, remove 2 bolts holding cylinder. Have new cylinder ready to install. pull shoes back from cylinder. remove line from cylinder and pull out of housing. Replace with new cylinder, first attaching line, then bolts. reset shoes into cylinder and make sure nothing else has slipped out of place (eg, parking brake cross bar and spring). Replace return springs on post. replace drum. open bleeder valve and allow gravity bleed until all air is out or bleed manually. any questions, lemme know.

Sep 05, 2010 | 1994 Pontiac Grand Am

1 Answer

The brake cylinder in the rear drum of a 93 ford ranger broke, how do i replace it


Remove wheel, brake drum, and brake shoes. The cylinder is the part the brake line goes into and it spreads the brake shoes apart when you brake.

Loosen the brake line but do not take off, unbolt the cylinder and then disconnect brake line. loosely connect the brake line to the new cylinder so you do not loose much brake fluid, bolt new cylinder in and then tighten the brake line.
Reinstall shoes. There should be a bleeding screw/grease head in the brake cylinder, loosen this and have someone step on the brake to bleed the line, have them hold the brake while you tighten the bleed screw. Do this as many times as necessary until brake fluid only with no air comes out.
Reinstall drum and tire, top off brake fluid.

Mar 16, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Where is the rear brake line on the master cylinder


the rear brake line is connected to the master cylinder inside the hub ..remove the tire and remove the hub the 2 bolts that hold the master cylinder in place are at top the line going into the cylinder itself is the brake line

Sep 26, 2009 | 1995 Chrysler Sebring

1 Answer

Rear drum brake caliber


You don't have calipers in drum brakes. you have wheel cylinders that activate the brakes when pedal is pressed. The brake cylinder is located at the top of the brake backing plate on the rear wheel. the brake line is screwed to it on the outside and two small bolt hold it in place. remove your brake springs, shoes etc., then remove the brake line and bolts. Before removing the brake line and bolts spray them with WD40 or something similar to loosen the rust around the fittings.

Jun 01, 2009 | 1993 Toyota Paseo

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1994 Pontiac Grand Am Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...