Question about Cars & Trucks

1 Answer

Water going into base/number 1 cyl has 20 lbs number 6 has 0 others are fine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

Blown head gaskets. If your car is old and has a lot of miles. Get a used engine and swap it. Or get another car. Really depends on much you like your car.

Posted on Apr 19, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are cylinder head torque specs?


Tighten the cylinder head bolts in the sequence shown in figure. Using the 4 step torque turn method, tighten according to the following values.
  1. Tighten center fasteners 1 thru 6 to 33 Nm (25 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  2. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  3. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs. ).



26083805-2jaahwjhyda0eguw15ciywpg-3-0.gif

Then tighten all fasteners 1 thru 10 90°turn . Do not use a torque wrench for this step.



26083805-2jaahwjhyda0eguw15ciywpg-3-2.gif

Feb 06, 2016 | 1999 Mitsubishi Eclipse

1 Answer

Torque specification for 1995 ford Taurus


4 Cyl Intake manifold bolts to heads = 15 to 23 Ft-lbs
6 Cyl 3.0L Step 1 = 11, step 2 = 21
6 Cyl 3.8L Step 1 = 7, step 2 = 15 & step 3 = 24 Ft-lbs
Tighten the bolts in secuence from center to out, alternating sides (front & rear); reaching the specified torque in several stages. I hope this helps. Take care.

May 25, 2014 | 1995 Ford Taurus

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

How many pound you torque for jeep wrangler 4 cyl. year 97 head gasket


Tightening Sequence

8 - 4 - 1 - 5 - 9
7 - 3 - 2 - 6 - 10

Pass 1 - 22 ft/lbs.
Pass 2 - 45 ft/lbs.
Pass 3 - # 7 - 100 ft/lbs.
Pass 3 - All others - 110 ft/lbs

May 26, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

I need to change my thermastat but can not locate it


REMOVAL & INSTALLATION (4 Cyl. eng.) CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Position a suitable drain pan under the radiator drain **** and drain the cooling system.
  2. On the 1MZ-FE engine, remove the air cleaner cap assembly. Be sure to label all wiring disconnected.
  3. Disconnect the water temperature switch harness from the water inlet housing (except 5S-FE engines).
  4. Remove the oil filter on 5S-FE engines. On the 1MZ-FE engines, remove the heater hose covering the housing.
  5. Loosen the hose clamp and disconnect the lower radiator hose from the water inlet housing.
  6. Remove the two nuts from the water inlet housing and remove the housing from the water pump studs.
  7. Remove the thermostat and rubber O-ring gasket from the water inlet housing. To install:
  8. Make sure all the gasket surfaces are clean. Clean the inside of the inlet housing and the radiator hose connection with a rag.
  9. Install the new rubber O-ring gasket onto the thermostat. On 2SE and 3S-FE engines, align the jiggle valve of the thermostat with the protrusion on the water inlet housing. On 5S-FE engines, align the jiggle valve with the upper side of the stud bolt. On 2VZ-FE and 3VZ-FE engines, align the jiggle valve with the stud bolt. Insert the thermostat into the housing. Fig. 1: Remove the thermostat housing from the engine with the coolant temperature sensor - 1MZ-FE engine 89553p18.jpg
    Fig. 2: Removing the thermostat from the engine - 1MZ-FE engine 89553p19.jpg
    Fig. 3: Always discard the old O-ring from the thermostat, if reusing the old component 89553p20.jpg
    Fig. 4: Always replace the thermostat with the correct temperature specifications 89553p21.jpg
    Fig. 5: Line-up the jiggle valve with the protrusion on the housing - 5S-FE engine 89553g10.gif

  10. Position the water inlet housing with the thermostat over the studs on the water pump and install the two nuts. Tighten the two nuts to 78 inch lbs. (9 Nm) on 4 cyl. engines, 2VZ-FE and 3VZ-FE; 14 ft. lbs. (20 Nm) and 69 inch lbs. (8 Nm) on 1MZ-FE engines. Fig. 6: Thermostat installation - 2VZ-FE and 3VZ-FE engines 89553g11.gif
    NOTE: Don't forget to install a new O-ring onto the water inlet pipe. Apply soapy water to the O-ring prior to installation.
  11. Connect the lower radiator hose to the inlet housing and install the hose clamp. On the 3VZ-FE, tighten the bolt holding the water inlet hose to the alternator belt adjusting bar to 14 ft. lbs. (20 Nm). On the 1MZ-FE engine, tighten the bolt retaining the water inlet pipe to the cylinder head to 14 ft. lbs. (20 Nm).
  12. Attach the water temperature switch connector.
  13. On the 1MZ-FE engines, install the heater hose removed.
  14. Install the oil filter and check the oil level if removed. Install the air cleaner cap assembly on the 1MZ-FE engines.
  15. Fill the cooling system with a good brand of ethylene glycol based coolant.
  16. Start the engine and inspect for leaks.
prev.gif next.gif

Oct 08, 2010 | 1990 Toyota Camry

1 Answer

What type of oil is best for a 2006 honda odyssey??? Tks


2006 HONDA ODYSSEY 3.5L 6-cyl Engine Code J35A7 2006 HONDA ODYSSEY 3.5L 6-cyl Engine Code J35A6

Engine Oil Grade 1......API* All TEMPS......5W-20 synthetic oil or conventional. Brand name you preference. Fram oil filter Part #PH7317 Honda oil filter part #15400-PLC-003 or 004
CAPACITIES: Engine, with filter..........4.3 liters After refill check oil level. Torque Oil Drain Plug.....29 ft/lbs

Jan 24, 2010 | 2007 Suzuki XL-7

1 Answer

Does any one have the torque specs and sec for a 1999 dodge neon 2.0 dohc


Standard Head Gasket

Step 1: Tighten bolts 1-6 to 25 Ft. Lbs. (34 N.m) and bolts 7-10 to 20 ft. lbs. (28 N.m).
Step 2: Tighten bolts 1-6 to 50 Ft. Lbs. (68 N.m) and bolts 7-10 to 20 ft. lbs. (28 N.m).
Step 3: (Repeat Step 2) Tighten bolts 1-6 to 50 Ft. Lbs. (68 N.m) and bolts 7-10 to 20 ft. lbs.
(28 N.m).
Step 4: Tighten all bolts an additional 1/4 turn (DO NOT use a torque wrench for this step).

Multi-Layer Steel (MLS) Head Gasket

Step 1: Tighten bolts 1-6 to 25 Ft. Lbs. (34 N.m) and bolts 7-10 to 20 ft. lbs. (28 N.m).
Step 2: Tighten bolts 1-6 to 50 Ft. Lbs. (68 N.m) and bolts 7-10 to 35 ft. lbs. (47 N.m).
Step 3: (Repeat Step 2) Tighten bolts 1-6 to 50 Ft. Lbs. (68 N.m) and bolts 7-10 to 35 ft. lbs.
(47 N.m).
Step 4: Tighten all bolts an additional 1/4 turn (DO NOT use a torque wrench for this step).

Tightening sequence

* Clean and oil threads before installation.

Dec 02, 2009 | 1999 Dodge Neon

2 Answers

I need to know the torque settings on the head for a 94 jeep grand cherokee laredo


Assuming the motor is an inline six
1.Middle bolt is number 1.Clockwise torque to 22 f/lb
2.Same pattern to 45 f/lb
3. same pattern to 100 f/lb
Be sure to use loctite 592 to the threads and some head gasket sealer to both sides of the head gasket.
Hope this helps

Oct 18, 2009 | 1994 Jeep Grand Cherokee

1 Answer

I need the torque specs for a ford 300 inline 6


Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Oct 08, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...