Question about 2006 Dodge Magnum

Open Question

I am needing to know if I replace my front end module with a used one will it still have to be programmed?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does any know what the code,P1383 to a,2000 Jaguar S-type is? Need answer ergent please!


That ended up being a false code in in order to Powertrain Control Module (PCM) should be re-programmed using WDS software release JTP759/14 or later

Jan 25, 2015 | Jaguar Cars & Trucks

1 Answer

What does error codes: B0100 and B0140 indicate wrong on a 2011 Buick LaCrosse CXL 3.6 V6 eng.?


B0100:
Perform trouble checking for the following: the front end sensor, the SDM module, the SDM wiring harness connector. Damage to the following parts needs replacement or repair. For the DTC B0100, detach the front end sensor1 connector and also detach the SDM connector. Perform trouble checking of the signal and voltage circuits between the SDM and the front end sensor for a short to voltage and for a short to ground. Reconnect all the SIR components and if the DTC B0100 is present then the front end sensor1 has to be changed.
B0104
Perform trouble checking for the following: the front end sensor, the SDM module, the SDM wiring harness connector. Damage to the following parts needs replacement or repair. For the DTC B0104, detach the front end sensor1 connector and also detach the SDM connector. Perform trouble checking of the signal and voltage circuits between the SDM and the front end sensor for a short to voltage and for a short to ground. Reconnect all the SIR components and if the DTC B0104 is present then the front end sensor2/right has to be changed.
i could not find anything on the B0140 code so i included the B0104 incase of typo

May 18, 2014 | 2011 Buick LaCrosse CXL

2 Answers

Trying to figure out how to bleed abs block on 2000 chevy silverado 1500


I am in the UK, so do not know this model, but I am a Bosch service tech and can tell you, if you have air in the ABS unit itself, you well need to connect to diagnostic tool with bleeding/venting program on it. The ABS pump needs to run and operate the solenoids to get the air out...

Sep 13, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

I had to chang the engine computer on my 02 town and country. Do I have to take it to chrysler to get it reprogramed for my van?


the town and country has a PCM ( power control module, located in front to the battery ) and a FCM ( front control module located on the front of the relay center next to the battery ) if either module is replaced they need to be programed with a DRBIII, so you will need to see your dealer.

Sep 09, 2011 | 2002 Chrysler Town & Country

2 Answers

I have a 2004 dodge ram 2500, Hemi. Yesterday the low beam went out on the driver side only but the high beam works on the same light bulb on the driver side. I tried replacing the light bulb but the same...


The Front Control Module is attached to the under hood fuse block with 4 screws, The FCM is the power supply to the headlamps, if all other lamps are working correctly the concern is most likely caused by a defective FCM. Verify the WT/DB wire, left low beam driver is good. If it is replace the FCM. you can use a FCM from a salvage yard, these modules do not need to be programmed for your vehicle.

Jan 23, 2011 | Dodge Ram 2500 Cars & Trucks

2 Answers

1999 cadilac deville. when you driver over speed bumps,you hear a sqeeking noice as the car bounces. noice comes front front end. #2. air blower works but does not turn off. Madr a switch to turn off and...


Okay....hope this helps......

#1-Front end squeek is coming from a bushing in the front end suspension....could be the rubber on your struts/schocks, balljoint, or tie rod bushings. Have to jack the car front end and start from one side to the other...a little bit of a pain to pin point.

#2-The fan selector switch is bad....which means the control panel has to be replaced.

#3-Brakes....couple of things.....brake pads may have been installed incorrectly...not seated correctly in the caliper....

Have you hit anything recently or run over a parking block or run over a curb???

Oct 14, 2010 | 1999 Cadillac DeVille

1 Answer

Front end damage air bags deployed is it fixable?


fixable possible depends on front end damage needs to go to bodyshop to have front end and frame" checked to if repairable and they should be able to replace airbags as well but will probably need a new airbag module also ? not that familiar with ford procedures and whos paying for this it wont be cheap and insurance may total it???

May 31, 2010 | 1997 Ford Taurus

1 Answer

1998 Ford Ranger, 4WD, 4.0 V6 Car stalling duri...


Taking it to a qualified repair shop that know's how to diagnose the problem using scan data . Not guessing an replacing parts .
Do you know what scan data is an how to obtain it ? You week end DIYER'S have no clue . An not listing to web sites an forums
007 Idle Speed Problems Scan Data for Idle This is why it costs $ 100.00 diagnostic fee .
Another site said pcm module may need updated programming. Where do I start?

Jul 01, 2017 | Cars & Trucks

2 Answers

Looking for a part for my nissan maxima 2008


This Body control module (known as a BCM) was 1st used on the 2007 Maxima, as far as programming it for your car only the dealer has the special programming equipment (nissan scanner and sofware) to do this job, as to the part it has only been used since Sept of 2007, so no aftermarket re-builders have it yet, (rebuilt modules is all that is avil for any car in the aftermarket) I have a huge collection of web sites for these kinds of parts (cdontrol modules) and there are no rebuilt BCM's aviliable for your car as of yet, it is to new, the lowest price I could find was $265.58 at this link, I don't recommend using a used part.
http://www.nissanpartswarehouse.com/partlocator/index.cfm?action=searchCatalogOEM&siteid=214315

Aug 11, 2009 | 2008 Nissan Maxima

1 Answer

Air bag replacement in 2003 grand am


That is the only sensor to trigger the bags. The new module needs to be programmed to the car by the dealer or someone with a scan tool capable of that.

Nov 12, 2008 | 2002 Chevrolet Cavalier Coupe

Not finding what you are looking for?
2006 Dodge Magnum Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...