Question about Jeep Cars & Trucks

1 Answer

What motors will fit in a 1998 jeep grand Cherokee 5.9l

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 14,585 Answers

96 to 99, 5.9l's only.

Posted on Apr 19, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: window motor replace 2001 jeep grand cherokee

You need to remove all the skrews from the door. Normaly there is one in the handle of the door, one behind the in door lach handel and one under the bump out for the arm rest on the door. Than you need to take a flat head skrew driver slowly priying the panel off. There are plastic clips on the backside of the panel it is ok if you brake a few.

Posted on May 01, 2009

  • 6982 Answers

SOURCE: 2001 Jeep grand cherokee motor knock 4.7 motor

First, if the noise is from the upper part of the engine and is more of a tapping than a knock, likely you have a problem in the valvetrain, most often a bad lifter or worn rocker arm. If the noise is low, deep inside, the noise is from a bearing. This is generally accompanied by lower than normal oil pressure. Regardless of the underlying cause, correcting the cause will not stop the knock. To do that correctly, the engine needs to be removed and all crankshaft bearings and the crankshaft itself need to be replaced (crank can sometimes be "undercut" and thicker bearing shells can be used depending upon the amount of wear.) If caught very early, sometimes only one bearing can be replaced in-car, but in 99% of all cases I have ever seen, most will fail again, sometimes more severely if done this way.

Posted on Dec 10, 2009

Testimonial: "Thanks"

michigan man
  • 3533 Answers

SOURCE: blower motor only works on high on 98 jeep grand

you need a temp limited switch and for the most part its close to the blower motor has a small screw on each side with a plug in the middle give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your Jeep dealership in the parts department and they be able to show you what i am talking about and print you off pictures and diagrams showing you where it is located wish you the best of luck Michigan Man.

Posted on Jan 04, 2010

ZJLimited
  • 17970 Answers

SOURCE: change a headlight assembly Jeep Grand Cherokee

Just need take off the screws; for details check the graphics and ilustrations in the Jeep ZJ Grand Cherokee Service Manual

Hope helps (remember rated this) Good luck..

Posted on Jan 20, 2010

  • 306 Answers

SOURCE: speakers for 1994 jeep grand cherokee

6.5" in all the doors dash is wierd. 2.75" but i have been able to squeez in a 3.5"

Posted on Feb 04, 2010

Testimonial: "thank you so much, that helps me out as lot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove heater blower motor?


1998 ATC Jeep Grand Cherokee Blower Resistor connector ...

? 0:55
www.youtube.com/watch?v=sDFLuenx9aw
Nov 14, 2012 - Uploaded by Freedomautomotive1
1998 ATC Jeep Grand Cherokee Blower Resistor connector Repair Kit (RARE 1/2 Year) ... How to Fix a Chrysler Blower FanThat Only Works on High - Duration: 16:51. ... JEEP2001 FIXING THE HEATER BLOWER CONTROL. ... Jeep Grand CherokeeCenter and Lower Dash Removal - Auto Repair Series ...

Sep 30, 2015 | 1998 Jeep Grand Cherokee

1 Answer

Open rear hatch 1998 Jeep Grand Cherokee without key


Hard one :-) climb over remove the cover,slide keeper off the lock fit new barrel and key.

Jul 21, 2014 | 1998 Jeep Grand Cherokee

1 Answer

Where is the blower motor resistor located on a 1998 jeep grand cherokee ?


it's either right behind the glove box or under the passenger side of the dash near the blower motor?

What problem are you having?

Jul 28, 2011 | 1998 Jeep Grand Cherokee

1 Answer

What motor is compatible with a 1999 grand jeep cheroke laredo? will one from a 1997 grand jeep limited fit


all teh smae motors ,hope your fitting a diesel and a manual gearbox ,then its a mans motor

Dec 03, 2010 | 1999 Jeep Grand Cherokee

1 Answer

What other kinds of motors will fit into a 2000 Jeep Grand Cherokee V8? I heard some dodge motors would fit but I don't know what year or what make.


dodge is mopar what you have is mopar (jeep) 97 to 2003 i think will fit there tuff to come across i had hard time myself

Jul 09, 2010 | 2000 Jeep Grand Cherokee

1 Answer

95 transfer case fit in 98


Depends if its the same model transfer case such as a nv231 or nv249 even a nv241 ....

May 11, 2009 | 1995 Jeep Grand Cherokee

4 Answers

Rear end (axle)


call jeep and give them last 9 digits of your vin and ask for three things -Differential Type,Gear ratio, and Track lock- They will give you
1) Dana 35 or 44
2) Gear Ratio 3.31 or 3.73
3) Track Lock - yes/no

Jan 11, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...