Question about 1994 Chevrolet S-10 Blazer

Open Question

How do I bleed the clutch on a 1994 4-wheel drive Chevy s-10 blazer

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: 1994 chevy s10 blazer 4x4 push button type

small sylinoid on the top of the transfer case needs replaced. easy to do. it has three vacumelines going to it just trun out and replace like a bolt.

Posted on Dec 13, 2008

  • 124 Answers

SOURCE: where is fuel relay

The fuel pump relay is only for the fuel pump priming when you turn on the key. After the vehicle starts the oil pressure switch takes over and runs the pump. If the pump is shutting off after the motor is running the oil pressure swith is probably bad. Let me know if i can help you further.

Posted on Dec 27, 2008

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

emissionwiz
  • 75197 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

  • 2 Answers

SOURCE: 1998 chevy s-10 blazer. 4 wheel drive does not

try putting it in neutral while it's running with foot on the brake then push 4 hi or 4 lo it should switch over then. Had the same problem on my 98 blazer the other day.

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed a hydralic clutch on a 2001 chevy blazer


You must reverse bleed it. Go here to learn how. You will need to buy the tool pictured.

Dec 05, 2012 | 2001 Chevrolet Blazer

1 Answer

My sister instead of turning on the rear wiper she turn on the 4x4 now it s making a strang e sound when is moving in reverse what i got is a chevy 1994 blazer s-10 4.3 l vector engine how do i get it...


Turn on engine. Put foot on brake & shift into neutral. Push button marked 2 wheel or 2x2. Shift back into park. Providing nothing is wrong with system it will now be in 2 wheel.

Sep 30, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

How do you turn off the four wheel drive on a 1994 s-10 blazer? the switch has only high & low


No 2H or neutral? If this model is considered an awd (all wheel drive) instead of 4 wheel drive you will not be able to turn it off.

Dec 18, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

93 Jimmy Electronic 4 Wheel Drive


If the Blazer is the same Year. I think the years are 1992 to 1994 will work as long as it's the 4L60E, and you have the manuel transfer case to activate the 4WD.
Good luck and keep me posted.

Jun 03, 2009 | 1994 Chevrolet S-10 Blazer

2 Answers

Name of the 4x4 computer module


It is called the transfer case control module, a dealer only part.

Feb 20, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

NO POWER TO FOUR WHEEL DRIVE


it could be a fuse or a relay not conducting the power to the switch have a local tech test it with a voltometer. it should be free to diagnos.

Jan 06, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

1994 chevy s10 blazer 4x4 push button type


small sylinoid on the top of the transfer case needs replaced. easy to do. it has three vacumelines going to it just trun out and replace like a bolt.

Dec 10, 2008 | 1994 Chevrolet S-10 Blazer

1 Answer

Gvw of chevy blazer s-10 1994 model


According to Edmunds.com the curb weight is 3,536 lbs.

Jun 17, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...