Question about Cars & Trucks

2 Answers

Reset throttle position sensor - Cars & Trucks

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

Check the wires at the plug first. They tend to break there. Pull on them one at a time, if they stretch, the wire is broke. They usually break inside the coating. After that replace the TPS.

Posted on Apr 19, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,355 Answers

You cant reset it, only replace it.

Posted on Apr 19, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The car says engine power reduce how can I reset that it's a 2004 Cadillac cts 3.6


Engine power reduced means it has a problem with the electronic throttle control system . You can't reset it , has DTC"S- diagnostic trouble codes stored in the computer . Something is worn , a position sensor in the gas pedal assembly or throttle position sensor on the throttle body . Your best bet , take it to a qualified repair shop ! or the dealer .
Drive by Wire Function and diagnostics by Wells

Drive by Wire training

Mar 25, 2017 | Cadillac CTS Cars & Trucks

1 Answer

Reset code for a 2011_akia rio throttle position sensor


Throttle Position Sensor Replacement - YourMechanic

www.yourmechanic.com > Auto Repair and Maintenance Services
When the throttle position sensor is repaired or replaced, it will need to have the minimum idle speed reset to factory specs, and the trouble codes will need to be ...

P0122 Code - Throttle Position Sensor/Switch A Circuit Low ...

www.obd-codes.com/p0122
Also includes links to other forum threads discussing the code. ... P0122 Code -Throttle Position Sensor/Switch A Circuit Low Input ... I have 6 codes that stay the same. all the rest don't stay after reset. codes are P0106,P0107,P0108,P0122 ...

2002-2005 Kia Sedona Throttle Position Sensor ... - YouTube

? 1:51
https://www.youtube.com/watch?v=JRwUK2Iem9s
Jul 11, 2011 - Uploaded by Jerry Ferguson
Kinda important - Before removing the old throttle position sensor, snap a photo of its position with your phone ...

Dec 26, 2015 | Cars & Trucks

1 Answer

Smog Filed due to error P0121 Throttle/Pedal Position Sensor/Switch A Circuit range/performance.


Replacing TPS will reset the light but will stay in memory until the computer is reset. For help to change throttle body sensor check out you tube :How To Install Replace Throttle Position Sensor Chevy Silverado GMC Sierra.

Mar 23, 2015 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

WHAT DOES P0123 MEAN?


SYMPTOM
P0123-THROTTLE POSITION SENSOR VOLTAGE HIGH

WHEN MONITORED
With the ignition ON and battery voltage above 10.4 volts .

SET CONDITION
Throttle Position Sensor voltage at the PCM goes above 4.5 volts for 3.2 seconds .

POSSIBLE CAUSES
  • Clock spring shorted
  • Throttle position sensor sweep
  • Intermittent condition
  • Throttle position sensor signal circuit shorted to 5 volt supply circuit
  • Throttle position sensor signal circuit shorted to battery voltage
  • Throttle position sensor internal failure
  • Sensor ground circuit open
  • Throttle position sensor signal circuit open
  • PCM
hope this helps, Tim 423 327 4108

Jun 06, 2014 | 2001 Dodge Dakota

1 Answer

Replace Throttle Position Sensor on my 2003 Chevy Suburban


Disconnect the wire connector to the sensor then remove the 2 screws and remove the sensor then put new one on and reset the computer with a code reader or a scan tool or take it to your local autoparts store (advance auto,autozone,ect.) and they can reset it for you at no charge to you.

Jan 20, 2012 | Cars & Trucks

2 Answers

1992 K1500, code 22, clicking noise from throttle body, will not accelerate properly, changed TPS with no change


OBD Code 22 - Throttle Position Sensor Error (Signal Low)
The Throttle Position sensor signals the Engine Control Module as to the current position of the engine throttle valve. The current throttle valve opening is based on the driver's input from the gas pedal. The ECM uses the information from this sensor to help calculate fuel delivery and spark timing.

Symptoms:
* Extended cranking, possible no-start condition
* Lack of power
* Erratic transmission operation

Common Problems:
* A failed Throttle Position Sensor (TPS) would be the most common causes for code 22
* Testing the TPS circuit would involve checking voltage and ground from the ECM-5v is the normal reading between the ECM reference circuit and the ECM ground circuit at the TPS connector. Checking the TPS signal circuit to the ECM would involve monitoring the TPS signal on a scan tool while jumping the 5v reference and the signal circuits. The TPS reading should go from high when the circuit is "jumpered" to low when the jumper is removed.


Keep us updated.

May 04, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

1 Answer

P0123, p0121


123 throttle position sensor/switch A circuit high input 121 throttle position sensor/switch A circuit range/performance problem if running fine try reset--- if running rough black smoke star problems check the TPS wiring ,connections,and mounting if looks good not grounding ,rubbing or damage to wiring than test TPS sensor

May 05, 2010 | 2002 Jeep Liberty

3 Answers

1999 Chevrolet Malibu Code PO122 problem fault code in the emission test and P0341 fault code in emssion test.


po341 is camshaft position sensor A bank 1 ckt range/perf and po122 istps/pedal position sensor A curcuit low input this is throttle position switch on side of throttle body!

Jun 05, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...