Question about 2006 Mercury Montego

Open Question

HOW TO REMOVE THE BUMPER ON A 2006 MERCURY MONTEGO

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: tail light removal 2006 Montego

The liner is much more durable that it appears. You should be able to fold the liner back enough to unscrew the three bolts holding the tail light unit.

Posted on Feb 23, 2009

Ad
  • 374 Answers

SOURCE: Change the oil on a 2005 Mercury Montego

Go to a automotive store and tell them you have a 2005 Mercury Montego and what engine it has if there is more then one model and get an oil filter and the oil. Put the car up on ramps and secure it making sure it won't roll back or fall while you are under it. get under the engine and look for the oil pan which should have a bolt in the bottom of it where you can drain the oil. Drain the oil in a proper container and then put the drain plug back in the pan. Then find the oil filter and unscrew it and remove it.. It could be full of oil so watch out and make sure the pan is underneath the filter. Wipe the base where the oil filter screws on and make sure the gasket from the old filter is not still on the engine. Get your new filter and take your finger and put it in one of your new containers of new oil and spread that on the gasket of the new filter. Screw on the filter until the gasket touches the base and then turn only a little more then a 1/4 to 1/2 turn tops. Do not over tighten the filter. Find out what oil the vehicle needs (probably 5-30) and look for the oil cap on a valve cover under the hood. It probably takes 5 quarts but check for sure in your manual or ask when you are at the automotive store. Put the oil in and put the filler cap back on. Now go start the vehicle and make sure you have oil pressure by either the oil pressure guage showing pressure or the oil pressure idiot light goes off and while running check under the car for any signs of leaks. If no leaks then back the car off the ramps and shut the car off on a level surface. Let it sit 10 minutes and check for leaks underneath the car and check the oil dipstick to make sure the proper level of oil is in the engine. Then you are set.

Always check your air filter when changing oil to make sure it is clean as that helps your engine run better and you save gas in the process. Good luck

It is also best to change oil when your engine is warmed up as well.

Posted on Mar 28, 2009

  • 5546 Answers

SOURCE: Mercury Montego won't start. Started 10 minutes

You could check the Inertia switch and see if the fuel pump is cut off.
If that is Okay I would disconnect the battery and see if the system reboots.
If it starts after that, go to Autozone or Oreillys for a free scan.
If it does not start, then try putting in the security code if you have a keypad. If no keypad, then try your other carkey, your ID chip may have died.

Posted on Dec 27, 2009

  • 2 Answers

SOURCE: I can't seem to compress the rear brake calipers

With a pair of needle nose pliers turn the pistons clockwise to set them back to base position. The V shape groves are not too deep on the pistons, so make sure you have gloves on, in case of the pliers slip out while turning it.

Posted on Apr 17, 2010

Keef2011
  • 160 Answers

SOURCE: 2006 mercury montego. DTC

These codes relate to an electronic throttle body fault. Normally its from dirt, hardening oil deposits jamming the throttle body movement. Try cleaning the throttle body first before going down the replacement route. Hope this helps....

Posted on Mar 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blend door actuator replacement 2005 2006 2007 mercury montego


Remove the glove box liner and you should be able to access it from there.

Apr 01, 2016 | 2005 Mercury Montego

1 Answer

What fuse controls the radio on a 2006 mercury montego


Owners manual will give fuse locations and identification

Jun 13, 2015 | 2006 Mercury Montego

1 Answer

How to remove the front bumper on 2006 mercury montego


remove all the mounting bolts under the front of it

Apr 18, 2015 | 2006 Mercury Montego

1 Answer

2006 mercury montego replace back blinker


most likely from inside the trunk, remove the cover to expose the light sockets they should twist one way then pull out then replace the bulb by pushing in a little and twisting (1156's and 1157's)

May 08, 2014 | 2006 Mercury Montego

2 Answers

Where is the electronic throttle body located on my 2006 mercury montego


Follow the air induction system up to the engine. It will be connected to the throttle body.

Aug 24, 2011 | 2006 Mercury Montego

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

How to change the amber side marker light bulb


This is not a solution, other than "Take it to the shop", but for our 2006 Montego, the shop is saying they have to take the bumper off to get at the marker light. I don't think that's a great design idea.

Nov 21, 2010 | 2005 Mercury Montego

1 Answer

Tail light removal 2006 Montego


The liner is much more durable that it appears. You should be able to fold the liner back enough to unscrew the three bolts holding the tail light unit.

Dec 19, 2008 | 2007 Mercury Montego AWD Sedan

Not finding what you are looking for?
2006 Mercury Montego Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...