Question about 2006 Mercury Montego

1 Answer

How to remove the front bumper on 2006 mercury montego

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 43,034 Answers

Remove all the mounting bolts under the front of it

Posted on Apr 18, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blend door actuator replacement 2005 2006 2007 mercury montego


Remove the glove box liner and you should be able to access it from there.

Apr 01, 2016 | 2005 Mercury Montego

1 Answer

2006 mercury montego replace back blinker


most likely from inside the trunk, remove the cover to expose the light sockets they should twist one way then pull out then replace the bulb by pushing in a little and twisting (1156's and 1157's)

May 08, 2014 | 2006 Mercury Montego

1 Answer

Front left ball joint for 06' Mercury Montego


The ball joints are part of the lower control arm . The control arm is not extremely difficult, but not easy either. First remove the nut on balljoint, then pull the ball joint out of the knuckle, that may take a pry bar, remove front control arm nut and bolt, and two bolts on rear of control arm bushing, reverse process to install. The Ford workshop manual says to replace the control arm nuts and bolts, but I hardly ever do. Have never had a problem. Torque front bolt to 111 lb-ft, and rear to 73 lb-ft. Hope that is good for you.
KIP. Martin, service manager Ford dealership.

Mar 25, 2014 | 2006 Mercury Montego

1 Answer

How do i check the transmission fluid on a 2005 mercury montego?


Locate the transmission after locating look for a tube with a dipstick in in make sure after you pull the stick the fluid is a red color it will say trans fluid with the car running and after removal of the stick wipe it clean replace it in the tube and remove it again the levels are marked on the stick

Sep 17, 2012 | 2006 Mercury Montego

2 Answers

Where is the electronic throttle body located on my 2006 mercury montego


Follow the air induction system up to the engine. It will be connected to the throttle body.

Aug 24, 2011 | 2006 Mercury Montego

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

Does my 2006 mercury montego have a transmission dipstick? if so, where is it-i watch to check to fluid it feels like the transmission is slipping


there is a dipstick on the bottom in front just to the right of the engine, only about 5'' long and it is yellow

Jul 28, 2011 | 2006 Mercury Montego

1 Answer

How to change the amber side marker light bulb


This is not a solution, other than "Take it to the shop", but for our 2006 Montego, the shop is saying they have to take the bumper off to get at the marker light. I don't think that's a great design idea.

Nov 21, 2010 | 2005 Mercury Montego

1 Answer

Tail light removal 2006 Montego


The liner is much more durable that it appears. You should be able to fold the liner back enough to unscrew the three bolts holding the tail light unit.

Dec 19, 2008 | 2007 Mercury Montego AWD Sedan

Not finding what you are looking for?
2006 Mercury Montego Logo

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...