Question about 2001 Chevrolet Chevrolet Malibu LS

Open Question

What size are the mounting bolts for the starter on a 2001 Malibu?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dennymulford
  • 1055 Answers

SOURCE: allen wrench size to fit caliper mounting bolt

some are 7/16 and some are 3/8 amd some are torx

Posted on May 30, 2009

Ad
duane_wong
  • 6826 Answers

SOURCE: how to remove and install starter motor on 2000

REMOVAL & INSTALLATION 2.4L Engine

  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Position a drain pan under the oil filter, then remove the oil filter.
  4. Remove the top starter bolt.
  5. Raise and safely support the vehicle.
  6. Remove the lower starter retaining bolt.
  7. If necessary, position the engine wiring harness aside.
  8. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  9. Remove the starter from the vehicle. To install:
  10. Raise the starter to the vehicle, then attach the wiring.
  11. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm). Fig. 1: When installing the starter on the 2.4L engine, tighten the mounting bolts to 66 ft. lbs. (90 Nm) 87952040.gif

  12. If moved, reposition the engine wiring harness.
  13. Attach the solenoid electrical connectors.
  14. Carefully lower the vehicle.
  15. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  16. Replace the oil filter.
  17. Fasten the air inlet duct to the throttle body.
  18. Connect the negative battery cable.
  19. Check the oil level and add if necessary.
  20. Start the engine, recheck the oil level and add if necessary.
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Remove the lower closeout panel.
  4. Remove the electrical leads. Fig. 2: Two electrical leads connect to the starter solenoid. The larger one has battery power as long as the battery is connected. The smaller one only has power when the key is turned to START 93202p09.jpg

  5. Remove the starter motor to engine bolts, then remove the starter from the vehicle. To install:
  6. Install the starter. Position one engine-to-starter bolt in the lower bolt hole, then finger-start the bolt.
  7. Connect the electrical leads to the starter. Tighten the cable to the solenoid to 106 inch lbs. (12 Nm).
  8. Install the starter-to-engine bolts and tighten to 37 ft. lbs. (50 Nm)
  9. Install the lower closeout panel.
  10. Lower the vehicle.
  11. Connect the negative battery cable.
prev.gif next.gif

Posted on Jan 21, 2011

  • 449 Answers

SOURCE: what is the torque suppossed to be on the motor mounts and the starter mounting bolts on a 2001 chevy malibu V6

Main cap bolt, 396-454 4-bolt (inner/outer) 110 ft.-lbs. 3/8 in. connecting rod bolt 50 ft.-lbs. 7/16 in. connecting rod bolt 67-73 ft.-lbs. Cylinder head bolts, long 75 ft.-lbs. Cylinder head bolts, short 65-68 ft.-lbs. Screw-in rocker arm studs 50 ft.-lbs. Intake manifold bolts (cast iron head) 25 ft.-lbs. Oil pump bolt 65 ft.-lbs. Cam sprocket bolts 20 ft.-lbs. motor mounts 85 ft.-lbs. Flywheel/flex plate bolts 60 ft.-lbs. Pressure plate bolts 35 ft.-lbs. Bell housing bolts 25 ft.-lbs. Exhaust manifold bolts 20 ft.-lbs.

Posted on Jun 10, 2012

  • 827 Answers

SOURCE: bolt size for a 93 4.3 transmission mount

Do not pass go, go directly to your local dealer and smooze the parts department cust service personnel -- note: stay away from the service department, they want the labor. the parts people would be very helpful and you might be able to grab a bolt right there, esp if it is fine thread.
Best regards
Ck

Posted on Jul 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove starter 2001 Lincoln Town Car


Print


Removal & Installation

  1. Remove or disconnect the following:

    Negative battery cable and properly isolate to prevent accidental reconnection Red solenoid safety cap Wires from solenoid 2 upper bolts 1 lower bolt and starter

    0996b43f8020875a.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Starter motor mounting


To install:
  1. Install or connect the following:

    Starter and lower mounting bolt 2 upper mounting bolts. Tighten all 3 bolts to 15-20 ft. lbs. (20-27 Nm). Wires from solenoid and tighten the nut to 40-50 inch lbs. Red solenoid safety cap Negative battery cable

Aug 15, 2012 | Lincoln Town Car Cars & Trucks

1 Answer

What is the torque suppossed to be on the motor mounts and the starter mounting bolts on a 2001 chevy malibu V6


Main cap bolt, 396-454 4-bolt (inner/outer) 110 ft.-lbs. 3/8 in. connecting rod bolt 50 ft.-lbs. 7/16 in. connecting rod bolt 67-73 ft.-lbs. Cylinder head bolts, long 75 ft.-lbs. Cylinder head bolts, short 65-68 ft.-lbs. Screw-in rocker arm studs 50 ft.-lbs. Intake manifold bolts (cast iron head) 25 ft.-lbs. Oil pump bolt 65 ft.-lbs. Cam sprocket bolts 20 ft.-lbs. motor mounts 85 ft.-lbs. Flywheel/flex plate bolts 60 ft.-lbs. Pressure plate bolts 35 ft.-lbs. Bell housing bolts 25 ft.-lbs. Exhaust manifold bolts 20 ft.-lbs.

Jun 10, 2012 | 2001 Chevrolet Malibu

1 Answer

How to change starter on 2006 malibu


Welcome to Fixya

Raise the front of the car then slide under the driver's side of the car and locate the starter on the engine where it meets the bell housing. Unplug the "S" connector from the terminal on the starter and lay it aside. Remove the nut from the "B" terminal with a wrench, then remove the battery cable from the starter. Locate the mounting bolts and loosen it. Slide the new starter then tighten the bolts.

Please click here if you need further assistance.

Thanks

Oct 09, 2011 | 2006 Chevrolet Malibu

1 Answer

Are there 2 or 3 bolts to remove when replacing a 2001 Chevy Impala 3.1 V6 engine Starter?


there r 2 main bolts which r either 13 or 15 mm...but u may also have a support bracket at the end of the starter where the wires bolt to the starter...that bolt can either be a 10 , 13, or 15 mm bolt holding it on

Jul 16, 2011 | 2001 Chevrolet Malibu

1 Answer

How to remove and install starter motor on 2000 malibu location of mounting bolts


REMOVAL & INSTALLATION 2.4L Engine
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Position a drain pan under the oil filter, then remove the oil filter.
  4. Remove the top starter bolt.
  5. Raise and safely support the vehicle.
  6. Remove the lower starter retaining bolt.
  7. If necessary, position the engine wiring harness aside.
  8. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  9. Remove the starter from the vehicle. To install:
  10. Raise the starter to the vehicle, then attach the wiring.
  11. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm). Fig. 1: When installing the starter on the 2.4L engine, tighten the mounting bolts to 66 ft. lbs. (90 Nm) 87952040.gif

  12. If moved, reposition the engine wiring harness.
  13. Attach the solenoid electrical connectors.
  14. Carefully lower the vehicle.
  15. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  16. Replace the oil filter.
  17. Fasten the air inlet duct to the throttle body.
  18. Connect the negative battery cable.
  19. Check the oil level and add if necessary.
  20. Start the engine, recheck the oil level and add if necessary.
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Remove the lower closeout panel.
  4. Remove the electrical leads. Fig. 2: Two electrical leads connect to the starter solenoid. The larger one has battery power as long as the battery is connected. The smaller one only has power when the key is turned to START 93202p09.jpg

  5. Remove the starter motor to engine bolts, then remove the starter from the vehicle. To install:
  6. Install the starter. Position one engine-to-starter bolt in the lower bolt hole, then finger-start the bolt.
  7. Connect the electrical leads to the starter. Tighten the cable to the solenoid to 106 inch lbs. (12 Nm).
  8. Install the starter-to-engine bolts and tighten to 37 ft. lbs. (50 Nm)
  9. Install the lower closeout panel.
  10. Lower the vehicle.
  11. Connect the negative battery cable.
prev.gif next.gif

Jan 21, 2011 | 2001 Chevrolet Malibu

1 Answer

HOW TO INSTALL A 2001 CHEVY MALIBU STARTER


Disconnect negative battery terminal, raise vehicle,remove splash sheild, if equipped. take wires off of solenoid on starter, remove starter mounting bolts, remember not to mix up wires!! --to install--put starter back in vehicle put in bolts,hook up wires, then replace cable back on battery.Locate the starter, it goes into the bellhousing of the transmission, that is where the engine and tranny meet. Easiest way is follow the wires coming from the positive battery post. It will be a big one. There are usually only two bolts holding it on. But first remove the wires going into it. Be careful with the main one coming from the battery, it is not fused and if grounded long enough will blow your battery up. Check out.Thanks.

Aug 27, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

2001 ford focus zx3 starter replacement instructions


2.0L DOHC Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Air cleaner outlet tube
    • Lower starter motor bolt
    • Two starter motor upper bolts
  3. Slide the starter motor from its mounting until you can gain access to the wiring.
    • Integral connector
    • Starter motor
To install:
  1. Install or connect the following:
    • Integral connector and tighten the retaining nuts to 61 inch lbs. (7 Nm)
f20d98a.gif
  • Starter motor to its mounting
  • Two starter motor upper bolts and tighten to 15–20 ft. lbs. (20–27 Nm)
  • Lower starter motor bolt and tighten to 15–20 ft. lbs. (20–27 Nm)
  • Air cleaner outlet tube
  • Negative battery cable
  • Dec 06, 2009 | 2001 Ford Focus

    1 Answer

    How can i get the oil pan out on a 2001 chevy malibu?


    2.2L Engines
    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Drain the engine oil.
    3. Remove or disconnect the following:

      Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan


    1. Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm).
    2. Accessory drive belt
    3. Negative battery cable

    4. Fill the engine with oil to the correct level.

    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Drain the engine oil.
    3. Remove or disconnect the following:

      Negative battery cable Accessory drive belt Lower A/C compressor mounting bolt Oil pan mounting bolts Oil pan

    To install:
    1. Apply a 0.13 inch (3.5mm) bead of the GM P/N 12378521 sealant around the perimeter of the oil pan and oil suction port opening.
    2. Install or connect the following:

      Oil pan. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).

      0900c1528024bb26.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Oil pan bolt sequence-2.2L engine
      Lower A/C compressor mounting bolt. Tighten the bolt to 37 ft. lbs. (50 Nm). Accessory drive belt Negative battery cable
    3. Fill the engine with oil to the correct level.
    3.1L Engine

    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Evacuate and recover the A/C system.
    3. Drain the engine oil.
    4. Remove or disconnect the following:
      WARNING DO NOT disconnect the refrigerant lines or allow the compressor to hang unsupported.


      Negative battery cable Accessory drive belt Upper and lower radiator hoses Right front wheel Inner fender splash shield Antilock Brake System (ABS) Wheel Speed Sensor (WSS) electrical connector Right front ball joint from the steering knuckle Right side outer tie rod end A/C compressor bolts and move the compressor aside


      Evaporator-to-accumulator A/C line Flywheel cover Engine cradle bolts Crankshaft balancer Starter motor Oil pan

    To install:

    0900c1528024bb27.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the oil pan mounting-3.1L and 3.5L engines

    1. Install or connect the following:

    Sep 02, 2009 | 2001 Chevrolet Malibu

    1 Answer

    Starter replacement in 2003 chevy malibu


    disconnect negative battery terminal, raise vehicle,remove splash sheild, if equipped. take wires off of solenoid on starter, remove starter mounting bolts, remember not to mix up wires!! --to install--put starter back in vehicle put in bolts,hook up wires, then replace cable back on battery.

    Aug 08, 2009 | 2003 Chevrolet Malibu

    Not finding what you are looking for?
    2001 Chevrolet Chevrolet Malibu LS Logo

    Related Topics:

    63 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8499 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...