Question about 2001 Dodge Grand Caravan
If you don't want to change a lot of parts from one engine to the other, stay around 2000 to 2003.
Posted on Apr 18, 2015
Any from 2000 to 2007.
Posted on Apr 18, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Yes, these are tough to get at from the top. Put the front on jack stands or ramps, and you can reach them a little easier from the bottom. You just need to reach up where the exhaust pipe comes down, and you can even see what you're doing this way.
Posted on Apr 02, 2009
JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.
GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.
Posted on Apr 29, 2009
your van has an obd1 setup with dodge all you should have to do is turn key to ign to off 5 times without starting vehicle and the check engine light will flash the code for example it will start off with a code 12 i believe saying the computer is functioning the check engine will flash 1 pause flash 2 pause and will repeat a total of three times just write down all the codes when it gets to code 55 it is done hope this is helpful
Posted on Jun 14, 2009
with most front wheel drives you must remove the passenger tire and reach through to the starter bolt with an extension and if I remember write with a 15 mm socket you can reach through and take out the bolt
Posted on Jun 20, 2009
Tips for a great answer:
Jan 03, 2016 | Dodge Cars & Trucks
Dec 18, 2015 | 2001 Dodge Grand Caravan
Jul 24, 2015 | Dodge Cars & Trucks
Jun 09, 2010 | 2001 Dodge Grand Caravan
May 06, 2010 | 2001 Dodge Caravan
Jan 21, 2010 | 2006 Dodge Grand Caravan
May 21, 2009 | 2001 Dodge Grand Caravan
Apr 26, 2015 | 2001 Dodge Grand Caravan
121 people viewed this question
Usually answered in minutes!