Question about Cars & Trucks

Open Question

2014 Solera 24s left side (driver's) turn signal and brake light not working.

Removed sections of the bargman 47-84-009 light module and swapped with those on the right side. The light modules work fine. Fuse diagram for Sprinter does not show separate fuses for right and left but I suspect that the lights have been modified. Cannot locate fuses. Some have posted that they are in the sewer compartment, but I did not see any panel there. Can anyone tell me where the fuse might be or if there might be another problem? A Clue - with running lights off, brake and turn signal and emergency flashers on right illuminate entire module. Only center rectangle illuminated on left.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: 1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block

Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Aug 05, 2008

Ad
  • 2 Answers

SOURCE: turn signals and flashers

Hello I had the same problem on my 04 monte. After changing bulbs ,checking wires etc. I finally took it to the dealer and they found out it was the hazard switch. After swapping it with a new one all lights, dash etc started working again and have not had another problem

Posted on Sep 05, 2008

  • 1 Answer

SOURCE: Turn signal stopped working 1990 Mercury Cougar

I had the same problem and the flasher is not located in the fuse box because it is not a normal flasher. the cougar has an electronic flasher unit that is located on the left side of the center console. the best and cheapest place to order a new one is amazon.com. they run about $30-$40

Posted on Jun 20, 2009

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

  • 49 Answers

SOURCE: right turn signal stays on will not flash left works.2001 jimmy

its your blinker box.. all major lights run through there

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the stop lamp or brake lamp fuse and panel for a 2007 cadillac cts?


Kevin , this is a very complex way of stoplamp control , I will post GM service Description and Operation of how they work an let you deside if you want to tackle this ! Do the center high mount brake lights work ?
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bas relay close and battery positive voltage is applied through the bas relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

There could be a code stored in the EBCM - electronic brake control module - DTC B3903 Stop Lamp Relay Circuit
DTC C0278 Brake Pedal Position Sensor Not Calibrated
there are several other codes that pertane to the brake lights . you could try Replaceing the bas relay !
Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet.

Jun 28, 2015 | 2007 Cadillac CTS 3.6L

2 Answers

Iwhere is the turn signal flasher located


  1. CAUTION: Prior to removal of module, it is necessary to upload module configuration information to a scan tool. This information needs to be downloaded into the new module once installed. For additional information; refer to Module Configuration. Ignore numbering on left of page


  2. There isn't a flasher...It is a module called the LCM ( Lighting Control module)...It needs to be replaced and requires a scan tool...Not a backyard project...




  3. Disconnect the battery ground cable.
  1. Remove the LH instrument panel lower insulator.
    1. Remove the pin-type retainers.
    1. Disconnect the courtesy lamp.
    1. Remove the LH instrument panel insulator.

iwhere-turn-signal-flasher-located-wtik1u3pjfqjepqdinj1lpkj-5-0.gif
  1. Position the LCM aside.
    1. Remove the screws.
    1. Release the locking tab.
    1. Position the LCM aside.

iwhere-turn-signal-flasher-located-wtik1u3pjfqjepqdinj1lpkj-5-2.gif
  1. Remove the LCM.
    1. Disconnect the electrical connectors.
    1. Remove the LCM.

iwhere-turn-signal-flasher-located-wtik1u3pjfqjepqdinj1lpkj-5-5.gif saailer

Jun 19, 2015 | 2000 Mercury Grand Marquis

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

I have 1999 Blazer with brake light out on driver side only. All other lights work. Replaced bulbs but nothing changed. Swapped the working lights from the other (right side) with the driver side but...


THE BRAKE LIGHTS DO GO THROUGH THE TURN SIGNAL SWITCH. TO TEST, REMOVE THE PLASTIC COVER AROUND THE THE COLUMN, UNDER THE STEERING WHEEL. THE TURN SIGNAL SWITCH MUST BE IN THE OFF POSITION. YOU WILL NEED TO EXPOSE THE WIRES UNDER THE STEERING WHEEL. DO NOT DISTURB THE WIRES IN THE YELLOW JACKET. THEY ARE AIRBAG WIRES. YELLOW PLUGS YELLOW JACKETED WIRES ARE AIRBAG.THE WIRE IN QUESTION HERE IS YELLOW BUT IT IS NOT IN A YELLOW JACKET, [ SLEEVE ]. NOW, PUSH ON THE BRAKE PEDAL. THE YELLOW WIRE IS LEFT REAR TURN & BRAKE WIRE, DARK GREEN IS RIGHT REAR TURN & BRAKE WIRE. BRAKE PEDAL DEPRESSED, IF BOTH OF THOSE WIRES HAVE POWER, ALL OF THAT IS OK. IF THE YELLOW WIRE HAS NO POWER TURN SIGNAL SWITCH IS BAD

Jan 16, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Brake light out on driver side only. All other lights work. Replaced bulbs but nothing changed. Swapped the working lights from the other (right side) with the driver side but nothing changed. So all...


yes they most certainly do go through the turn signal switch and from what you are saying that would be the first piece that i would check. you can find the harness for it on the left side of the steering columm it is a long(about 4")black plug you could try a new one from an auto parts store they run about $20-$30 just unplug the old one and plug inthe new one however if it is this piece that has gone bad i do not recommend for you to try to replace it yourself as it is rather involved and it does require some specialty tools i hope this was helpful

Jan 16, 2011 | 1999 Chevrolet Blazer

1 Answer

I have a Chevy 2500 4X4 with brake lights not working. I have all other lights working. I only have one brake light working when I turn on the right turn signal then my left brake light will work. What's...


What year?

Sounds like a turn signal switch. Earlier models would use the same bulb for the brake and turn signal. The turn signal switch will interrupt power to the brake light and route the signal to either the left or right bulb depending on with way you where turning. Usually you can wiggle the turn signal switch and get the brake light to work momentarily when this is the problem.

Newer vehicles use a lighting module that looks for inputs from the turn signal switch and brake pedal switch and then decides where to send power. This module is also know to go bad.

Oct 11, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

Jaguar xj6 break light cancels signal


Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

2 Answers

No left turn signal or brake light on trailer,checked all fuses they were fine I had no power at the plug in at the back of truck on the left side for brake light or turn signal the running lights are...


I had the same problem on 06 ram, the problem is one of the controll modules under the fuse panel under the hood on the drivers side. My trailer mechanic told me this was a common problem and dodge will only charge about 700 dollars to replace it. he solved my problem by installing a converter on the wires to the tail lights of the truck then running down to the trailer plug. it was most likely caused by a short in the trailer and dodge in their infinate wisdom failed to put a fuse between the trailer and control module. and by the way even though this is a manufacturing defect they will not warranty the module. hope this helps.

Jul 08, 2009 | 2006 Dodge Ram 2500

1 Answer

WHERE ARE THE FLASHING LIGHTS FUSES OR SIGNAL LIGHTS IN THE DIAGR


From my Haynes repair manual "the turn signal/hazard flasher is located on the backside of the left instrument panel fuse/relay box"
in the picture they have removed the drivers side knee bolster (if you remove it, the module is in the window, you'll see,) and it is a square looking black module, (not the old silver round type,) plugged into the back of the fusebox. It is above and to the left of the brake release lever.
Just reach up under the dash and pull it out.

Mar 23, 2009 | 2000 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...